ENGINEERING YOUR SUCCESS. aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding Pneumatic Actuator Products Cylinders, Guided Cylinders and Rotary Actuators Catalog 0900P-E ! WARNING FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users h aving technical expertise. It is important that you analyze all aspects of your application including consequences of any failure, and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice. Offer of Sale The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated on the separate page of this document entitled “Offer of Sale”. © Copyright 2011, 2009, 2008 Parker Hannifin Corporation. All Rights Reserved Catalog 0900P-E Pneumatic Actuator Products Warning, Offer of Sale Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics 1 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Pneumatic Actuator Products Product Selection Chart Catalog 0900P-E Index Application Engineering Data A Tie Rod Cylinders 3MA/4MA Series, 3MAJ/4MAJ Series, 4MNR Series, ACVB Option, LPSO Option, S Series, C Series B ISO Cylinders P1D Series, P1A Series C Round Body Cylinders SR Series, SRM Series, SRD/SRDM Series, SRX Series, P1L Series, P Series D Compact Cylinders P1M Series, P1M Series with Tooling Plate, P1M Series Swing Clamp, LP/LPM Series, C05 Series, P1G Series E Guided Cylinders P5T Series, P5T2 Series, P5L Series, HB Series, P5E Series F Rodless Cylinders OSP-P, P1X Series, P1Z Series, RC Series, GDL G Rotary Actuators PV Series, PRN(A) Series, WR Series, PTR Series, B671/F672 Series, HP Series, P5W Series H Pneumatic Grippers For Complete Information, Refer to Catalog 1900-2 J Air Motors P1V-S Series For Complete Information, Refer to Catalog PDE2554TCUK-ul K Complementary Products Linear Alignment Couplers, Flow Controls, 4TK Air Oil Tanks, PRL Series, Transition Kits L Electronic Sensors Solid State, Reed and Proximity Sensors M Industrial Shock Absorbers Industrial Shock Absorbers (Linear Decelerators) N Fax Forms, Safety Guide, Offer of Sale Application FAX Forms P Industrial Shock Absorbers Fax Forms, Safety Guide, Offer of Sale Pneumatic Grippers Rotary Actuators Rodless Cylinders Compact Cylinders Round Body Cylinders Tie Rod Cylinders Engineering Data ISO Cylinders Guided Cylinders Complementary Air Motors Products Electronic Sensors Compact Pneumatic Cylinders Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E1 P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Section E Section E – Compact Pneumatic Cylinders P1M Series • 10 Bore Sizes: 12mm through 100mm • Short Overall Length • Smooth Extruded Exterior • Flexible Porting • Piston Position Sensing P1M Series with Tooling Plate • 32, 40 and 50 mm Bore Sizes • Short Overall Length • Flexible Porting • Industry Interchangeable • Non-Rotating Capability P1M Series Swing Clamp • 32, 40 and 50 mm Bore Sizes • Short Overall Length • 90° Clamping Rotation • Right Hand or Left Hand Rotation • Flexible Porting LP / LPM Series • Low Profile Design • 6 Mounting Styles • 8 Bore Sizes from 9/16″ to 4″ • Strokes from 1/8″ to 6″ • Permanent Lubrication C05 Series • 6 Bore Sizes – 8mm though 63mm • Short Stroke Cylinder • Block Style Mount • Single and Double Acting Available P1G Series • 6, 10, and 16mm Bore Sizes • 5, 10, and 15mm Stroke Lengths • Cartridge Style Mount • Single Acting, Non-Lube Design • Nickel Plated Brass Body with Stainless Steel Rod for Corrosion Resistance Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E2 E Catalog 0900P-E Section E Overview E3 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E P1M Series Extra Low Profile Pneumatic Cylinder Contents Features…………………………………………………………………….E4 Ordering Information……………………………………………………E5 Specifications……………………………………………………………..E6 Technical Data…………………………………………………………….E7 Dimensions…………………………………………………………. E8-E11 Mounting Dimensions…………………………………………. E12-E15 Double Rod Style Dimensions……………………………… E16-E17 Rod End Accessories…………………………………………. E18-E19 Service Kits………………………………………………………………E20 Extra Low Profile Pneumatic Cylinders P1M Series E4 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Features Z-Profile Piston Seal Dynamic piston seal features two rounded micro sealing edges for maximum wear compensation and rounded grooves for retaining lubrication. Sensors Recessed, flush position sensors available in PNP, NPN or REED styles. Construction Innovative 3-piece bolted design. Ports Optional NPTF or BSPP ports at no extra charge. Bumpers Optional bumpers provide noise reduction and impact resistance. Urethane for 12-25mm bore sizes, Hytrel® for 32-100mm bore sizes. Cylinder Body Smooth anodized aluminum exterior provides wearresistant surface. Unique Internal Transfer Tube Provides a passage that can be used for remote porting. Rounded Lip Rod Wiper Seal Non-lube urethane rod seal provides dual function as rod seal and rod wiper to eliminate leakage and prevent contamination from entering the cylinder. Piston Rod Stainless steel or hard chrome plated carbon steel piston rods (stainless steel standard on 25mm bore and under). Mounting Holes Counter bored tapped or through holes for mounting. Rod Ends Four standard piston rod ends to meet a variety of requirements. Piston Magnet Located behind the piston in a separate magnet carrier, the piston magnet is used for electronic piston sensing. (Increases cylinder body length.) High Strength Rod Bearing Multilayer PTFE with steel backing. Extra Low Profile Version The Extra Low Profile Bearing Version allows us to provide the most compact cylinder possible. This bearing version is recommended for applications that require shorter stroke lengths or that are light duty. It is available in stroke lengths up to 50mm in the smaller bore sizes and 150 mm in the larger bore sizes. Long Bearing Version The Long Bearing Version provides additional rod bearing and piston bearing support and also includes a magnetic piston with bearing strip for greater piston bearing support. This Long Bearing version is required for stroke lengths beyond the Extra Low Profile maximum stroke length and is recommended for higher duty applications. Hytrel® is a registered trademark of DuPont. Extra Low Profile Pneumatic Cylinders P1M Series E5 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Catalog 0900P-E Ordering Information How to Order P1M Series Cylinders P1M 032 C / D C P 6 G 012 Bore Size 012 12mm 016 16mm 020 20mm 025 25mm 032 32mm 040 40mm 050 50mm 063 63mm 080 80mm 100 100mm Cylinder Style C Basic No Mtgs. A Double Rear Clevis 1,3 B Single Rear Clevis 1,3 F Foot Mount 1,4 J Front Flange 1 H Rear Flange 1, 3 Insert “/ ” to denote Special Function D Double Acting K Double Rod R Single Acting Spring Return 6 E Single Acting Spring Extend 4 Piston/Seal Material Without Magnet 2 C No Bumpers Class 1 Std. Temp. Seals G No Bumpers Class 5 Fluorocarbon Seals B With Bumpers Class 1 Std. Temp. Seals 7 With Magnet 5 (Not available on Spring Extend Models) N No Bumpers Class 1 Std. Temp. Seals M With Bumpers Class 1 Std. Temp. Seals 7 Maximum Stroke Lengths Bore ELP Bearing Version Long Bearing Version Single Acting Version Min. Stroke* Max. Stroke Min. Stroke* Max. Stroke Standard Stroke 12 3 50 4 200 5,10 16 3 50 4 200 5,10 20 3 50 8 200 5,10 25 3 50 8 200 5,10 32 3 100 9 320 5,10 40 3 100 7 320 5,10 50 3 100 13 320 10, 20, 25 63 3 100 18 500 10, 20, 25 80 3 150 23 500 10, 20, 25 100 3 150 18 500 10, 20, 25 * Minimum Stroke for Double Rod cylinders: 12-63mm Bores is 5mm 80 &100mm Bores is 10mm Piston Rod & Bearings Extra Low Profile Rod Bearing P Chrome Plated Steel Rod Not Available on 12-25mm Bores Y Stainless Steel Rod Standard on 12-25mm Bores and Spring Extend Models Long Rod Bearing 2 C Chrome Plated Steel Rod Not Available on 12-25mm Bores A Stainless Steel Rod Standard on 12-25mm Bores and Spring Extend Models Stroke in mm Rod Threads Inch 4 Male 9 Female Metric 5 Male 6 Female 3 Special Rod End Ports BSPP G Ported Each End H Both Ports Head J Both Ports Cap K Both Ports Cap Face 3 NPTF (Not available on 12-25mm Bores) N Ported Each End M Both Ports Head L Both Ports Cap P Both Ports Cap Face 3 NOTES: 1 Fitted with Mounting Accessory 2 Magnetic Piston Option must be specified along with Long Rod Bearing option to achieve Long Bearing Version 3 Porting Options ‘K’ and ‘P’ (Both ports cap face) not available with rear mountings 4 Single Acting Spring Extend available with stainless steel rod only. 5 For information regarding sensors, please refer to Electronic Sensors section. 6 Spring return is short bearing version only. 7 Bumper only available on head end for spring extend. Bumper only available on cap end for spring return. For ordering purposes, when special options or common modifications are requested, the factory will assign a sequential part number in place of the model number. (Revised 12-03-13) Extra Low Profile Pneumatic Cylinders P1M Series E6 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Specifications Material Specifications 1 Piston Rod 12mm to 25mm bores: Stainless Steel 32mm to 100mm bores: Chrome Plated Carbon Steel Std., Optional Stainless Steel (Stainless Steel std. on single-acting spring extend) Piston Rod Seal Polyurethane Piston Rod Bearing 2 Multilayer PTFE with Steel Backing End Covers Anodized Aluminum Alloy Assembly Cap Screws Stainless Steel / Zinc-Plated Steel O-Rings Nitrile Rubber, NBR Cylinder Body Anodized Aluminum Alloy Piston Aluminum Alloy Piston Seal Nitrile Rubber, NBR Magnetic Piston Bearing 3 Brass (12-25mm) Nylon (32-100mm) Magnet Plastic Coated Magnetic Material Bumpers Polyurethane Return Spring Chrome Silicon Wire High Temperature Option O-Rings Fluorocarbon, FPM Piston Rod Seal Fluorocarbon, FPM Piston Seal Fluorocarbon, FPM Additional Data Working Pressure Max.10 Bar Air Standard Temperature -20°C to +80°C -4°F to +176°F High Temperature Service -10°C to +121°C +14°F to 250°F 1 Dimensions not otherwise noted are listed in millimeters (mm) 2 Excludes 12-25mm bore Rod Style Y 3 Magnetic Piston option is not available on Spring Extend models. Spring Return Spring Extend Single Acting Cylinders Bore (mm) Return Loads Extend Loads Standard Stroke Lengths (mm) 2 Max (lbs) Min (lbs) Max (lbs) Min (lbs) 12 2.8 1.0 2.5 1.1 5,10 16 3.5 1.5 4.0 2.0 5,10 20 3.5 1.5 5.0 2.5 5,10 25 4.7 2.5 6.0 2.5 5,10 32 6.0 3.5 6.5 4.0 5,10 40 7.2 4.7 7.0 4.0 5,10 50 14.3 6.0 18.0 8.0 10, 20, 25 63 14.3 6.0 18.0 8.0 10, 20, 25 80 26.0 14.0 25.0 10.0 10, 20, 25 100 26.0 14.0 25.0 10.0 10, 20, 25 NOTES: 1 Overall Length to be the same as double-acting models with comparable bearing, piston and porting configuration. 2 Single-acting cylinders are available in standard stroke lengths. Custom stroke lengths are available upon request. 3 Spring Extend cylinders available with stainless steel rod only. 4 Magnetic Piston Option is not available on Spring Extend Models. Bore Double Acting* Single Acting** Single Rod Double Rod Spring Return Spring Extend 12 1.4 2.0 – 1.0 16 1.6 2.0 0.6 1.0 20 2.2 3.0 0.7 1.5 25 2.2 3.0 0.7 1.5 32 1.0 1.0 – – 40 1.0 1.0 – – 50 0.8 0.8 – – 63 1.0 1.0 – – 80 0.8 0.8 – – 100 1.0 1.0 – – * Bumpers at both ends ** Bumpers at end opposite of spring only. Additional Length for Bumper Option Extra Low Profile Pneumatic Cylinders P1M Series E7 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Catalog 0900P-E Technical Data Forces, Weights, Air Consumption Bore (mm) Area (cm2) Piston Rod Extend Force* (N) Retract Force* (N) Weight Air Consumption (Liters)** Dia. (mm) Area (cm2) Zero Stroke (kg) Per 10mm Stroke (kg) 12 1.13 6 0.28 67 50 0.060 0.016 0.0139 16 2.01 8 0.50 120 91 0.090 0.022 0.0246 20 3.14 10 0.78 188 142 0.150 0.032 0.0385 25 4.91 10 0.78 294 247 0.170 0.034 0.0633 32 8.0 12 1.1 482 414 0.260 0.044 0.1050 40 12.6 16 2.0 754 633 0.370 0.060 0.1620 50 19.6 20 3.1 1178 989 0.570 0.085 0.2530 63 31.2 20 3.1 1870 1681 0.860 0.098 0.4140 80 50.3 25 4.9 3016 2721 1.460 0.146 0.6690 100 78.5 25 4.9 4712 4417 2.390 0.155 1.0430 *Theoretical cylinder force at 600 kPa (6 bar). ** Free air consumption per 10mm stroke length for an extend and retract stroke at 600 kPa (6 bar) Front Profiles by Bore Size To retract cylinder apply air to port #2 To extend cylinder apply air to port #4 For a double rod cylinder, pressurize port #2 to retract the piston rod into the head containing the ports. *For 12mm to 16mm bores, although the location of ports #2 and #4 are reversed, porting functions shown above apply. Bores 12-25mm Bores 32-50mm Bores 63-100mm Porting Configurations Both Ports Cap Both Ports Head* Both Ports Cap Face 2 4 2 4 2 4 2 4 Double Rod Both Ports One End Extra Low Profile Pneumatic Cylinders P1M Series E8 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Dimensions Extra Low Profile Version RT BG1 HL HL BG2 EE 2 Places WH PL NB NB E2 E1 E R SQ. 4 2 ALL PORTING CONFIGURATIONS MOUNTING HOLE CONFIGURATION BOTH PORTS HEAD EE1 (Orifice Ø) 2 Places BOTH PORTS HEAD Bores 12-50mm: (2) ØR2 Thru, 180° Apart. (4) ØR1 C’Bore; Bores 63-100mm: (4) ØR2 Thru, (8) ØR1 C’Bore I92 ØR2 ØR1 Ø MM I53 (I73) + Stroke L° L° I12 I91 ZL3 (ZH3) + Stroke OPTIONAL PORTING CONFIGURATIONS MOUNTING HOLE CONFIGURATION BOTH PORTS CAP OR CAP FACE, PORTS AT HEAD & CAP RT BG1 HL HL BOTH PORTS CAP EE1 (Orifice Ø) 2 Places ZL1 (ZH1) + Stroke PL EE 2 Places WH HEAD & CAP PORTED BOTH PORTS CAP FACE WH ZL1 (ZH1) + Stroke EE1 (Orifice Ø) 2 Places EE 2 Places PL ZL1 (ZH1) + Stroke WH PL EE1 (Orifice Ø) 2 Places EE 2 Places I51 (I71) + Stroke I51 (I71) + Stroke P1 P2 P3 P4 I51 (I71) + Stroke ØR1 ØR2 I91 I91 I12 I12 I12 4 2 2 4 Note: Magnetic Dimensions in Parentheses Extra Low Profile Pneumatic Cylinders P1M Series E9 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Bore Rod AF AM KF KK WH I12 SW Style 6 Style 9 Style 5 Style 4 Style 6 Style 9 Style 5 Style 4 Style 4, 9 & 6 Style 5 12 6 6 5.4 9 8 M3x0.5 #8-32 M5x0.8 #8-32 3.5 5 3 5 16 8 8 5.4 10 8 M4x0.7 #8-32 M6x1.0 #8-32 3.5 5.5 3 7 20 10 7 7 12 8 M5x0.8 #10-32 M8x1.25 #10-32 4.5 6.5 4 9 25 10 12 10 15 9.5 M6x1.0 1/4-28 M10x1.25 1/4-28 5 7.5 4 9 32 12 13 13.3 20.5 12.7 M8x1.25 5/16-24 M12x1.25 5/16-24 7 8 5 10 40 16 13 18.3 20.5 16 M8x1.25 3/8-24 M14x1.5 3/8-24 7 8 5.5 13 50 20 15 17.6 26 19.5 M10x1.5 1/2-20 M18x1.5 1/2-20 8 7.5 5.5 16 63 20 15 17.6 26 19.5 M10x1.5 1/2-20 M18x1.5 1/2-20 8 7.5 5.5 16 80 25 21 24.3 32.5 25.5 M16x2.0 5/8-18 M22x1.5 5/8-18 10 11 6 21 100 25 27 27 32.5 28.5 M20x2.5 3/4-16 M22x1,5 3/4-16 12 11 6 21 Bore P3 P4 PL PM R R1 R2* RT Non-Magnetic Magnetic ELP I51 I53 ZL1 ZL3 I71 I73 ZH1 ZH3 Max Stroke 12 13.5 13.5 5 8.5 15.5 5.8 3.5 M4 22 17 25.5 20.5 33 28 36.5 31.5 50 16 15.5 18 5 9 20 7.4 3.5 M4 23.5 18.5 27 22 34.5 29.5 38 33 50 20 24.5 21.5 5 9 25.5 9 5.5 M6 24 19.5 28.5 24 34 29.5 38.5 34 50 25 27.5 24.5 7 9 28 9 5.5 M6 28.5 22.5 33.5 27.5 38.5 32.5 43.5 37.5 50 32 31.5 28.5 8 10.5 34 10.5 5.5 M6 36.5 28.5 43.5 35.5 46 37.5 53 44.5 100 40 23 33 7.5 9.5 40 10.5 5.5 M6 38.5 29.5 44.5 36.5 47.5 39.5 54.5 46.5 100 50 25 41.5 8 10 50 13.5 7.5 M8 38.5 32.5 46.5 40.5 47.5 41.5 55.5 49.5 100 63 30 53 8 11 60 13.5 9.5 M10 39.5 34 47.5 42 51.5 46 59.5 54 100 80 33 69.5 11.5 11.5 77 16.5 11 M12 52 43 62 53 62.5 53.5 72.5 63.5 150 100 36.5 87.5 12 12 94 17 11 M12 57 48.5 69 60.5 71.5 63 83.5 75 150 Catalog 0900P-E Dimensions Extra Low Profile Version SW Wrench Flats KK AM WH KF Thread x Depth AF WH For special rod ends, specify “3” in model number and give desired WH, AM or AF and KK or KF (length dimensions in millimeters). Jam nut is supplied when cylinder is ordered with Style 4 or Style 5 rod end. *“R2 thru” not available on 12 and 16mm Bores. Bore BG1 BG2 E E1 E2 EE EE1 HL I91 I92 L NB P1 P2 BSPP NPTF 12 16.5 11.5 27 31 14 M5 – 1 8 3.5 3.5 26 5.5 25 9.5 16 17 12 31.5 35 16 M5 – 1.2 8 4 4 20 7 29.5 9.5 20 19 14,5 38.5 42.5 19,5 M5 – 1.3 10 4.5 4.5 20 8 35 13.5 25 21 15 41.5 45.5 21 M5 – 1.8 10 5 5 20 8.5 38.5 14 32 25 17 48 56 24 G1/8 1/8 2.7 10 4 4 25 9.5 45.5 16.5 40 25.5 17.5 56 62.5 28 G1/8 1/8 3.4 10 4 4 20 11.5 51 12 50 29.5 23.5 67 74.5 33.5 G1/8 1/8 4 14 5 5 20 14.5 63 54.5 63 34 28 82 86 40.5 G1/8 1/8 5 18 6.5 8 20 17.5 73.5 64 80 43 34 98 106.5 48.5 G1/4 1/4 5.5 22 8.5 10 20 25.5 92 79.5 100 44 35.5 119 126.5 59.5 G1/4 1/4 6 22 8.5 10 20 31.5 111.5 97.5 Style 5/Style 4 Style 6/Style 9 (Revised 04-30-12) Extra Low Profile Pneumatic Cylinders P1M Series E10 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Dimensions Long Bearing Version RT BG HL HL BG2 ZH2 + Stroke EE 2 Places WH PM NB NB E2 E1 E R SQ. 4 2 ALL PORTING CONFIGURATIONS MOUNTING HOLE CONFIGURATION BOTH PORTS HEAD EE1 (Orifice Ø) 2 Places BOTH PORTS HEAD Bores 12-50mm: (2) ØR2 Thru, 180° Apart. (4) ØR1 C’Bore; Bores 63-100mm: (4) ØR2 Thru, (8) ØR1 C’Bore I92 ØR2 ØR1 Ø MM I72 + Stroke L° L° I12 I9 OPTIONAL PORTING CONFIGURATIONS MOUNTING HOLE CONFIGURATION BOTH PORTS CAP OR CAP FACE, PORTS AT HEAD & CAP BG1 RT BG HL HL BOTH PORTS CAP EE1 (Orifice Ø) 2 Places ZH + Stroke PL EE 2 Places WH HEAD & CAP PORTED BOTH PORTS CAP FACE WH ZH + Stroke EE1 (Orifice Ø) 2 Places EE 2 Places PL ZH + Stroke WH PL EE1 (Orifice Ø) 2 Places EE 2 Places I7 + Stroke I7 + Stroke P1 P2 P3 P4 I7 + Stroke ØR1 ØR2 I9 I91 I12 I12 I12 4 2 2 4 Extra Low Profile Pneumatic Cylinders P1M Series E11 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Catalog 0900P-E Dimensions Long Bearing Version SW Wrench Flats KK AM WH KF Thread x Depth AF WH Style 5/Style 4 Style 6/Style 9 For special rod ends, specify “3” in model number and give desired WH, AM or AF and KK or KF (length dimensions in millimeters).. Jam nut is supplied when Style 4 or Style 5 rod end is specified. Note: Magnetic piston and longer rod bearing are standard with Long Bearing Version. * “R2 thru” not available on 12 and 16mm Bores. Bore Rod MM AF AM KF KK WH I12 SW Style 6 Style 9 Style 5 Style 4 Style 6 Style 9 Style 5 Style 4 Style 4, 9 & 6 Style 5 12 6 6 5.4 9 8 M3x0.5 #8-32 M5x0.8 #8-32 3.5 5 3 5 16 8 8 5.4 10 8 M4x0.7 #8-32 M6x1.0 #8-32 3.5 5.5 3 7 20 10 7 7 12 8 M5x0.8 #10-32 M8x1.25 #10-32 4.5 6.5 4 9 25 10 12 10 15 9.5 M6x1.0 1/4-28 M10x1.25 1/4-28 5 7.5 4 9 32 12 13 13.3 20.5 12.7 M8x1.25 5/16-24 M12x1.25 5/16-24 7 8 5 10 40 16 13 18.3 20.5 16 M8x1.25 3/8-24 M14x1.5 3/8-24 7 8 5.5 13 50 20 15 17.6 26 19.5 M10x1.5 1/2-20 M18x1.5 1/2-20 8 7.5 5.5 16 63 20 15 17.6 26 19.5 M10x1.5 1/2-20 M18x1.5 1/2-20 8 7.5 5.5 16 80 25 21 24.3 32.5 25.5 M16x2.0 5/8-18 M22x1.5 5/8-18 10 11 6 21 100 25 27 27 32.5 28.5 M20x2.5 3/4-16 M22x1.5 3/4-16 12 11 6 21 Bore BG BG1 BG2 E E1 E2 EE EE1 HL I7 I72 I9 I91 I92 L BSPP NPTF 12 21.5 16.5 11.5 27 31 14 M5 – 1 8 38.5 33.5 3.5 3.5 3.5 26 16 22 17 12 31.5 35 16 M5 – 1.2 8 40.5 35.5 5.5 4 4 20 20 24.5 19 14.5 38.5 42.5 19.5 M5 – 1.3 10 40 35.5 10.5 4.5 4.5 20 25 24.5 21 15 41.5 45.5 21 M5 – 1.8 10 42.5 36.5 10.5 5 5 20 32 27.5 25 17 48 56 24 G1/8 1 8 2.7 10 48 40 14 4 4 25 40 27.5 25.5 17.5 56 62.5 28 G1/8 1/8 3.4 10 49.5 41.5 14 4 4 20 50 31.5 29.5 23.5 67 74.5 33.5 G1/8 1/8 4 14 49.5 43.5 13 5 5 20 63 37 34 28 82 86 40.5 G1/8 1/8 5 18 54.5 49 6.5 6.5 8 20 80 43 43 34 98 106.5 48.5 G1/4 1/4 5.5 22 62.5 53.5 9.5 8.5 10 20 100 44 44 35.5 119 126.5 59.5 G1/4 1/4 6 22 71.5 63 9.5 8.5 10 20 Bore NB P1 P2 P3 P4 PM R R1 R2* RT ZH ZH2 Min Stroke Max Stroke 12 5.5 25 9.5 13.5 13.5 8.5 15.5 5.8 3.5 M4 42 37 4 200 16 7 29.5 9.5 15.5 18 9 20 7.4 3.5 M4 44 39 4 200 20 8 35 13.5 24.5 21.5 9 25.5 9 5.5 M6 44.5 40 8 200 25 8.5 38.5 14 27.5 24.5 9 28 9 5.5 M6 47.5 41.5 8 200 32 9.5 45.5 16.5 31.5 28.5 10.5 34 10.5 5.5 M6 55 47 9 320 40 11.5 51 12 23 33 9.5 40 10.5 5.5 M6 56.5 48.5 7 320 50 14.5 63 54.5 25 41.5 10 50 13.5 7.5 M8 57.5 51.5 13 320 63 17.5 73.5 64 30 53 11 60 13.5 9.5 M10 62.5 57 18 500 80 25.5 92 79.5 33 69.5 11.5 77 16.5 11 M12 72.5 62.5 23 500 100 31.5 111.5 97.5 36.5 87.5 12 94 17 11 M12 83.5 75 18 500 (Revised 04-30-12) Extra Low Profile Pneumatic Cylinders P1M Series E12 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Dimensions – F Style Mounting Foot Mounting – Style F Bore Kit Part Number AB AH AJ AT AU E3 I7 K1 LY TR 12 P1M-4DMF 4.5 17 19.5 2 8 44 29.5 2.8 34 35 16 P1M-4FMF 4.5 19 19.5 2 8 48 33.5 2.8 38 39 20 P1M-4HMF 6.5 24 20.5 3.2 9.2 62 42 4 47 50 25 P1M-4JMF 6.5 26 22.5 3.2 10.7 66 46 4 50.5 52 32 P1M-4KMF 6.5 30 25 3.2 11.2 71 54 4 62 60 40 P1M-4LMF 6.5 33 25 3.2 11.2 78 61 4 67.5 67 50 P1M-4MMF 9 39 29.5 3.2 14.7 95 72.5 5 80 82 63 P1M-4NMF 11 46 31 3.2 16.2 113 32 5 91.5 100 80 P1M-4PMF 13 59 35 4.5 19.5 140 42 7 117 118 100 P1M-4QMF 13 71 39 6 23 162 53 7 138 139 WF AU AU AT K1 AJ SA 1-6* + Stroke ZA 1-6* + Stroke I7 TR E3 (4) – ØAB AH LY KF x AF Deep (See Opposite Page) Please note bearing, piston and porting configuration for selecting proper dimensions. Bore ELP Version Non-Magnetic ELP Version Magnetic Long Bearing Version Style 5 End Length Adjustment Both Ports Head Optional Porting Min. ** Stroke Both Ports Head Optional Porting Min.** Stroke Both Ports Head Optional Porting Min.** Stroke SA1 ZA1* SA2* ZA2* SA3 ZA3* SA4 ZA4* SA5 ZA5* SA6 ZA6* 12 5 35.3 10 40.3 15 16 46.3 21 51.3 4 21.5 51.8 26.5 56.8 4 1.5 16 6.5 36.8 11.5 41.8 14 17.5 47.8 22.5 52.8 4 23.5 53.8 28.5 58.8 4 2 20 7.5 41.2 12 45.7 18 17.5 51.2 22 55.7 8 23.5 57.2 28 61.9 8 2 25 7.5 44.7 13.5 50.7 18 17.5 54.7 23.5 60.7 8 21.5 58.7 27.5 64.7 8 2.5 32 12.5 52.5 20.5 60.7 18 21.5 61.7 29.5 69.9 9 24 64 32 72.2 9 1 40 13.5 53.7 21.5 61.9 17 23.5 63.7 31.5 71.9 7 25.5 65.7 33.5 73.9 7 1 50 9.5 58.7 15.5 64.9 22 18.5 67.7 24.5 73.9 13 20.5 69.7 26.5 75.9 13 -0.5 63 8 60.2 13.5 65.7 30 20 72.2 25.5 77.7 18 23 75.2 28.5 80.7 18 -0.5 80 13 74.5 22 83.5 33 23.5 85 32.5 94 23 23.5 85 32.5 94 23 1 100 14.5 83.5 23 92 33 29 98 37.5 106.5 18 29 98 37.5 106.5 18 -1 * For strokes less than ‘Min. Stroke’, only one bracket will be supplied at rod end. ** Dimensions shown apply only for Rod End Styles 4, 6 and 9. For Rod End Style 5, please include the above length adjustment. Note: Foot Bracket mounting is not available with cap face porting Extra Low Profile Pneumatic Cylinders P1M Series E13 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E KF Thread x Depth AF WF W WF KF Thread x Depth AF SW Wrench Flats KK W AM WF SW Wrench Flats KK AM WF Bore Kit Part Number E FB MF R TF UF ELP Version Non-Magnetic ELP Version Magnetic Long Bearing Version Style 5 Rod End Length Adjustment Both Ports Head Optional Porting Both Ports Head Optional Porting Both Ports Head Optional Porting ZB1* ZB2* ZB3* ZB4* ZB5* ZB6* 12 P1M-4DMB 25 4.5 5.5 – 45 55 30.5 35.5 41.5 46.5 47 52 1.5 16 P1M-4FMB 30 4.5 5.5 – 45 55 32 37 43 48 49 54 2 20 P1M-4HMB 39 6.5 8 – 50.5 62 34 38.5 44 48.5 50 54.5 2 25 P1M-4JMB 42 6.5 8 – 53 65 37.5 43.5 47.5 53.5 51.5 57.5 2.5 32 P1M-4KMB 48 5.5 8 34 58 68 45.5 53.5 54.5 62.5 57 65 1 40 P1M-4LMB 54 5.5 8 40 66 76 46.5 54.5 56.5 64.5 58.5 66.5 1 50 P1M-4MMB 67 6.5 9 50 79 90 50.5 56.5 59.5 65.5 61.5 67.5 -0.5 63 P1M-4NMB 80 9 9 60 97 112 52 57.5 64 69.5 67 72.5 -0.5 80 P1M-4PMB 99 11 11 77 116 134 63 72 73.5 82.5 73.5 82.5 1 100 P1M-4QMB 117 11 11 94 137 154 70.5 79 85 93.5 85 93.5 -1 Bore AF AM KF KK W WF SW Style 9 Style 6 Style 4 Style 5 Style 9 Style 6 Style 4 Style 5 Styles 9, 6, 4 Style 5 Styles 9, 6, 4 Style 5 12 5.4 6 8 9 #8-32 M3X0.5 #8-32 M5X0.8 8 9.5 13.5 15 5 16 5.4 8 8 10 #8-32 M4x0.7 #8-32 M6x1.0 8 10 13.5 15.5 7 20 7 7 8 12 #10-32 M5x0.8 #10-32 M8x1.25 6.5 8.5 14.5 16.5 9 25 10 12 9.5 15 1/4-28 M6x1.0 1/4-28 M10x1.25 7 9.5 15 17.5 9 32 13.3 13 12.7 20.5 5/16-24 M8x1.25 5/16-24 M12x1.25 9 10 17 18 10 40 18.3 13 16 20.5 3/8-24 M8x1.25 3/8-24 M14x1.5 9 10 17 18 13 50 17.6 15 19.5 26 1/2-20 M10x1.5 1/2-20 M18x1.5 9 8.5 18 17.5 16 63 17.6 15 19.5 26 1/2-20 M10x1.5 1/2-20 M18x1.5 9 8.5 18 17.5 16 80 24.3 21 25.5 32.5 5/8-18 M16x2.0 5/8-18 M22x1.5 9 10 20 21 21 100 27 27 28.5 32.5 3/4-16 M20x2.5 3/4-16 M22x1.5 11 10 22 21 21 Catalog 0900P-E Dimensions – Style J Mounting Bores 32-100mm Bores 12-25mm Front Flange Mounting – Style J MF W WF ZB1-6* + Stroke E R TF UF (4) ØFB KF x AF Deep * Dimensions shown apply only for Rod End Styles 4, 6 and 9. For Rod End Style 5, please include the above length adjustment. Please note bearing, piston and porting configuration for selecting proper dimensions. For special rod threads, specify “3” in model number and give desired AM or AF, WF and KK or KF (length dimensions in millimeters).. Rod End Dimensions Front Mounts F & J Foot Mounting – Style F Foot Flange Mounting – Style J Foot Mounting – Style F Foot Flange Mounting – Style J E TF UF (2) ØFB (Revised 04-30-12) Extra Low Profile Pneumatic Cylinders P1M Series E14 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Bore Kit Part Number E FB MF R TF UF 12 P1M-4DMB 25 4.5 5.5 – 45 55 16 P1M-4FMB 30 4.5 5.5 – 45 55 20 P1M-4HMB 39 6.5 8 – 50.5 62 25 P1M-4JMB 42 6.5 8 – 53 65 32 P1M-4KMB 48 5.5 8 34 58 68 40 P1M-4LMB 54 5.5 8 40 66 76 50 P1M-4MMB 67 6.5 9 50 79 90 63 P1M-4NMB 80 9 9 60 97 112 80 P1M-4PMB 99 11 11 77 116 134 100 P1M-4QMB 117 11 11 94 137 154 Bore ELP Version Non-Magnetic ELP Version Magnetic Long Bearing Version Style 5 Rod End Length Adjustment Both Ports Head ZF1* Optional Porting ZF2* Both Ports Head ZF3* Optional Porting ZF4* Both Ports Head ZF5* Optional Porting ZF6* 12 26 31 37 42 42.5 47.5 1.5 16 27.5 32.5 38.5 43.5 44.5 49.5 2 20 32 36.5 42 46.5 48 52.5 2 25 35.5 41.5 45.5 51.5 49.5 55.5 2.5 32 43.5 51.5 52.5 60.5 55 63 1 40 44.5 52.5 54.5 62.5 56.5 64.5 1 50 49.5 55.5 58.5 64.5 60.5 66.5 -0.5 63 51 57.5 63 68.5 66 71.5 -0.5 80 64 73 74.5 83.5 74.5 83.5 1 100 71.5 80 86 94.5 86 94.5 -1 Catalog 0900P-E Dimensions – Style H Mounting ZF1-6* + Stroke MF E R TF UF (4) ØFB E TF UF (2) ØFB Bores 32-100mm Bores 12-25mm Rear Flange Mounting – Style H Please note bearing, piston and porting configuration for selecting proper dimensions. Note: Rear Flange mounting is not available with cap face porting. * Dimensions shown apply only for Rod End Styles 4, 6 and 9. For Rod End Style 5, please include the above length adjustment. Extra Low Profile Pneumatic Cylinders P1M Series E15 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Bore ELP Version Non-Magnetic ELP Version Magnetic Long Bearing Version Style 5 Rod End Length Adjustment Both Ports Head XD1* Optional Porting XD2* Both Ports Head XD3* Optional Porting XD4* Both Ports Head XD5* Optional Porting XD6* 12 34.5 39.5 45.5 50.5 51 56 1.5 16 37 42 48 53 54 59 2 20 42 46.5 52 56.5 58 62.5 2 25 47.5 53.5 57.5 63.5 61.5 67.5 2.5 32 55.5 63.5 64.5 72.5 67 75 1 40 59.5 66.5 68.5 76.5 70.5 78.5 1 50 68.5 74.5 77.5 83.5 79.5 85.5 -0.5 63 72 78.5 84 89.5 87 92.5 -0.5 80 91 100 101.5 110.5 101.5 110.5 1 100 105.5 114 120 128.5 120 128.5 -1 Bore Double Clevis Kit Part Number Single Clevis Kit Part Number** CB CD/EK EW F FL L MR O UB 12 P1M-4DMT P1M-4DME 5 5 5 4 14 10 6.5 14.5 10 16 P1M-4FMT P1M-4FME 6.5 5 6.5 4 15 11 6.5 16.5 12 20 P1M-4HMT P1M-4HME 8 8 8 5 18 13 10 21 16 25 P1M-4JMT P1M-4JME 10 10 10 5 20 15 11 25.5 20 32 P1M-4KMT P1M-4KME 18 10 18 5 20 15 10 41.5 36 40 P1M-4LMT P1M-4LME 18 10 18 6 22 16 10 41.5 36 50 P1M-4MMT P1M-4MME 22 14 22 7 28 21 14 50.5 44 63 P1M-4NMT P1M-4NME 22 14 22 8 30 22 14 50.5 44 80 P1M-4PMT P1M-4PME 28 18 28 10 38 28 18 64 56 100 P1M-4QMT P1M-4QME 32 22 32 13 45 32 22 72 64 Catalog 0900P-E Dimensions ØCD MR L FL XD1-6* + Stroke F O CB UB ØEK h9 Style A Style B Rear Clevis Mounts – Styles A & B Please note bearing, piston and porting configuration for selecting proper dimensions. * Dimensions shown apply only for Rod End Styles 4, 6 and 9. For Rod End Style 5, please include the above length adjustment. ** Single Clevis Kit can be used as mounting bracket for double clevis cylinders. Double Clevis Kit can be used as mounting kit for single clevis cylinders. Note: Rear Clevis mounts are not available with cap face port. EW Extra Low Profile Pneumatic Cylinders P1M Series E16 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Double Rod Style C and J Style C Heads Ported at Each End or One End Refer to “Single Rod” (pages E6-E9) for dimensions not listed below. Both rods will be supplied with same rod ends unless called out as special. Style J Bore Basic Cylinder – Style C ELP Version Non-Magnetic ELP Version Magnetic Long Bearing Version K51 XH2 ZH7 Min. Stroke K71 XH1 ZH6 Min. Stroke I75 XH ZH5 Min. Stroke 12 22 29 25.5 15 40 47 43.5 5 45.5 52.5 49 5 16 23.5 30.5 27 14 40 47 43.5 5 46.5 53.5 50 5 20 24 33 28.5 18 38 47 42.5 8 46.5 55.5 51 8 25 28.5 38.5 33.5 18 38.5 48.5 43.5 8 46.5 56.5 51.5 8 32 36.5 50.5 43.5 18 46 60 53 9 50.5 64.5 57.5 9 40 37.5 51.5 44.5 17 47.5 61.5 54.5 14 51.5 65.5 58.5 12 50 38.5 54.5 46.5 22 47.5 63.5 55.5 20 51.5 67.5 59.5 20 63 39.5 55.5 47.5 30 51.5 67.5 59.5 20 57.5 73.5 65.5 20 80 52 72 62 33 62.5 82.5 72.5 25 62.5 82.5 72.5 25 100 57 81 69 33 71.5 95.5 83.5 25 71.5 95.5 83.5 25 Please note bearing, piston and porting configuration for selecting proper dimensions. Bore Flange Mounting – Style J Rod End Dimensions ELP Version Non-Magnetic ELP Version Magnetic Long Bearing Version WF WH XH6 ZB7 Min.* Stroke XH7 ZB8 Min.* Stroke XH8 ZB9 Min.* Stroke Styles 4, 6, 9 Style 5 Styles 4, 6, 9 Style 5 12 39 35.5 5 57 53.5 5 62.5 59 5 13.5 15 3.5 5 16 40.5 37 5 57 53.5 5 63.5 60 5 13.5 15.5 3.5 5.5 20 43 38.5 8 57 52.5 8 65.5 61 8 14.5 16.5 4.5 6.5 25 48.5 43.5 18 58.5 53.5 8 66.5 61.5 8 15 17.5 5 7.5 32 60.5 53.5 18 70 62.5 9 74.5 67.5 9 17 18 7 8 40 61.5 54.5 17 71,5 64.5 14 75.5 68.5 12 17 18 7 8 50 64.5 56.5 22 73.5 65.5 20 77.5 69.5 20 18 17.5 8 7.5 63 65.5 57.5 30 77.5 69.5 20 83.5 75.5 20 18 17.5 8 7.5 80 82 72 33 92.5 82.5 25 92.5 82.5 25 20 21 10 11 100 91 79 33 105.5 93.5 25 105.5 93.5 25 22 21 12 11 * Note: Please consult factory for cylinders that require shorter than minimum stroke length listed above. WH WH + Stroke I75 / K51 / K71* + Stroke ZH5-7* + Stroke XH / XH1 / XH2* + 2x Stroke WF WH + Stroke ZB7-9* + Stroke XH6-8* + 2x Stroke Basic Cylinder – Style C Flange Mounting – Style J Extra Low Profile Pneumatic Cylinders P1M Series E17 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Catalog 0900P-E Double Rod Style F Style F Bore ELP Version Non-Magnetic ELP Version Magnetic Long Bearing Version SA7 XH3 Min.* Stroke SA8 XH4 Min.* Stroke SA9 XH5 Min.* Stroke 12 10 49 5 28 67 5 33.5 72.5 5 16 11.5 50.5 5 28 67 5 34.5 73.5 5 20 12 53 8 26 67 8 34.5 75.5 8 25 13.5 58.5 8 23.5 68.5 5 31.5 76.5 8 32 20.5 70.5 8 29.5 80 5 34.5 84.5 9 40 21.5 71.5 7 31.5 81.5 5 35.5 85.5 12 50 15.5 74.5 12 24.5 83.5 10 28.5 87.5 20 63 13.5 75.5 20 25.5 87.5 10 31.5 93.5 20 80 22 92 23 32.5 102.5 15 32.5 102.5 25 100 23 101 23 37.5 115.5 15 37.5 115.5 25 Please note bearing, piston and porting configuration for selecting proper dimensions. Bore Rod End Dimensions WF WH Styles 4, 6, 9 Style 5 Styles 4, 6, 9 Style 5 12 13.5 15 3.5 5 16 13.5 15.5 3.5 5.5 20 14.5 16.5 4.5 6.5 25 15 17.5 5 7.5 32 17 18 7 8 40 17 18 7 8 50 18 17.5 8 7.5 63 18 17.5 8 7.5 80 20 21 10 11 100 22 21 12 11 WF WF + Stroke SA7-9* + Stroke XH3-5* + 2x Stroke * Note: Please consult factory for cylinders that require shorter than minimum stroke length listed above. Foot Mounting – Style F Heads Ported at Each End or One End Refer to “Single Rod” (pages E6-E9) for dimensions not listed below. Both rods will be supplied with same rod ends unless called out as special. Extra Low Profile Pneumatic Cylinders P1M Series E18 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Rod End Accessories O CL CM ØEK ER LE CE KK Th’d x A Depth E Rod Clevis – Metric Bore Kit Part Number A E CE KK ER LE EK (h9) CM CL O 12 P1M-4DRC 7 9.5 16 M5x0.8 6.5 7 5 5 9.5 14.5 16 P1M-4FRC 11 11 21 M6x1.0 8 10 5 6.5 11 16.5 20 P1M-4HRC 8.5 16 25 M8x1.25 10.5 11.5 8 8 16 21 25 P1M-4JRC 10.5 19 30 M10x1.25 13 14 10 10 19 25.5 32 P1M-4KRC 16 22 Dia. 30 M12x1.25 12 14 10 18 36 41.5 40 P1M-4LRC 16 22 Dia. 30 M14x1.5 12 14 10 18 36 41.5 50/63 P1M-4MRC 20 28 Dia. 40 M18x1.5 16 20 14 22 44 50.5 80 P1M-4PRC 23 38 Dia. 50 M22x1.5 21 27 18 28 56 64 100 P1M-4QRC 24 44 Dia. 55 M22x1.5 24 31 22 32 64 72 Rod Clevis – Inch Bore Kit Part Number A E CE KK ER LE EK (inch) +0, -0.002 CM CL (inch) O (inch) 12 P1M-4DRC-T 6 9.5 16 #8-32 6.5 7 3/16 5 0.375 0.563 16 P1M-4FRC-T 6 11 21 #8-32 8 10 3/16 6.5 0.437 0.625 20 P1M-4HRC-T 6 16 25 #10-32 10.5 11.5 5/16 8 0.625 0.875 25 P1M-4JRC-T 8 19 30 1/4-28 13 14 3/8 10 0.750 1.031 32 P1M-4KRC-T 16 22 Dia. 30 5/16-24 12 14 3/8 18 1.437 1.687 40 P1M-4LRC-T 16 22 Dia. 30 3/8-24 12 14 3/8 18 1.437 1.687 50/63 P1M-4MRC-T 20 28 Dia. 40 1/2-20 16 20 1/2 22 1.750 2.125 80 P1M-4PRC-T 23 38 Dia. 50 5/8-18 21 27 3/4 28 2.250 2.625 100 P1M-4QRC-T 24 44 Dia. 55 3/4-16 24 31 7/8 32 2.500 2.875 Jam Nut for Style 5 Dimensions in mm Bore Size Part Number KK M S 12 L073800080 #8-32 1/8 11/32 16 L073800080 #8-32 1/8 11/32 20 L073800100 #10-32 1/8 3/8 25 L073800200 1/4-28 5/32 7/16 32 L073800300 5/16-24 3/16 1/2 40 L073800400 3/8-24 7/32 9/16 50 L073800600 1/2-20 5/16 3/4 63 L073800600 1/2-20 5/16 3/4 80 L073800800 5/8-18 3/8 15/16 100 L073800900 3/4-16 27/64 1-1/8 Jam Nut for Style 4 Dimensions in inches S M KK Bore Size Part Number KK M S 12 L075540005 M5x0.8 2.7 18 16 L075540006 M6x1.0 3.2 10 20 L075540008 M8x1.25 4 13 25 L075540010 M10x1.25 5 17 32 L075540012 M12x1.25 6 19 40 L075540014 M14x1.5 7 22 50 L075540018 M18x1.5 8 27 63 L075540018 M18x1.5 8 27 80 L075540022 M22x1.5 11 32 100 L075540022 M22x1.5 11 32 Rod Clevis Jam Nuts Extra Low Profile Pneumatic Cylinders P1M Series E19 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E KK Th’d x A Depth EM ØCK ER LE CA E Rod Eye – Metric Bore Kit Part Number A E CA KK ER LE CK EM 12 P1M-4DRE 7 9.5 Sq. 16 M5x0.8 6.5 7 5 5 16 P1M-4FRE 8 11 Sq. 25 M6x1.0 8 14 5 6.5 20 P1M-4HRE 8.5 16 Sq. 25 M8x1.25 10.5 11.5 8 8 25 P1M-4JRE 10.5 19 Sq. 30 M10x1.25 13 14 10 10 32 P1M-4KRE 15 22 Dia. 30 M12x1.25 12 14 10 18 40 P1M-4LRE 14 22 Dia. 30 M14x1.5 12 14 10 18 50/63 P1M-4MRE 18.5 28 Dia. 40 M18x1.5 16 20 14 22 80 P1M-4PRE 22 38 Dia. 50 M22x1.5 21 27 18 28 100 P1M-4QRE 22 44 Dia. 55 M22x1.5 24 31 22 32 Rod Eye – Inch Bore Kit Part Number A E CA KK ER LE CK (inch) EM 12 P1M-4DRE-T 6 9.5 Sq. 16 #8-32 6.5 7 3/16 5 16 P1M-4FRE-T 6 11 Sq. 25 #8-32 8 14 3/16 6.5 20 P1M-4HRE-T 6 16 Sq. 25 #10-32 10.5 11.5 5/16 8 25 P1M-4JRE-T 8 19 Sq. 30 1/4-28 13 14 3/8 10 32 P1M-4KRE-T 12 22 Dia. 30 5/16-24 12 14 3/8 18 40 P1M-4LRE-T 11 22 Dia. 30 3/8-24 12 14 3/8 18 50/63 P1M-4MRE-T 18 28 Dia. 40 1/2-20 16 20 1/2 22 80 P1M-4PRE-T 21 38 Dia. 50 5/8-18 21 27 3/4 28 100 P1M-4QRE-T 21 44 Dia. 55 3/4-16 24 31 7/8 32 Catalog 0900P-E Rod End Accessories Rod Eye Extra Low Profile Pneumatic Cylinders P1M Series E20 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Service Kits Bore Single Rod Cylinders Double Rod Cylinders Class 1 Seals Class 5 Seals* Class 1 Seals Class 5 Seals* 12 P1M-6DRN P1M-6DRV P1M-6DRT P1M-6DRP 16 P1M-6FRN P1M-6FRV P1M-6FRT P1M-6FRP 20 P1M-6HRN P1M-6HRV P1M-6HRT P1M-6HRP 25 P1M-6JRN P1M-6JRV P1M-6JRT P1M-6JRP 32 P1M-6KRN P1M-6KRV P1M-6KRT P1M-6KRP 40 P1M-6LRN P1M-6LRV P1M-6LRT P1M-6LRP 50 P1M-6MRN P1M-6MRV P1M-6MRT P1M-6MRP 63 P1M-6NRN P1M-6NRV P1M-6NRT P1M-6NRP 80 P1M-6PRN P1M-6PRV P1M-6PRT P1M-6PRP 100 P1M-6QRN P1M-6QRV P1M-6QRT P1M-6QRP * No Bumpers Included E21 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E P1M Series Tooling Plate Extra Low Profile Pneumatic Cylinder Contents Features / Benefits…………………………………………………….E22 Ordering Information………………………………………………… E23 Cylinder Specifications……………………………………………….E24 Performance Data………………………………………………. E25-E27 Dimensions……………………………………………………….. E28-E31 Mounting Dimensions…………………………………………. E32-E33 Double Rod Style Dimensions……………………………… E34-E35 Mounting and Service Kits…………………………………………..E36 Tooling Plate Cylinder P1M Series E22 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Features and Benefits Flush Sensor Groove provides protection and a “clean” design. Three piece bolted construction allows for quick servicing. Internal Transfer Tube allows for flexible porting, providing space savings. NPT, BSPP, or BSPT Ports offer flexibility. Standard and custom mounting hole configuration Anodized, smooth aluminum construction available. provides superior corrosion resistance. “Long Bearing” and Magnetic Piston provide maximum bearing support for increased load carrying capability. P1M Series Tooling Plate Flexible Porting Options Double Rod, Both Ports Cap (Radial) Both Ports Head* Head and Cap Ported (Radial) Double Rod, Both Ports Head* Double Rod, Head and Cap Ported (Radial) To retract cylinder, apply air to port #2. To extend cylinder, apply air to port #4. * Both Ports Head [BSPP ports (M5) for 12-25mm bores and 1/8″ NPTF ports for 32-50mm bores] is the standard porting configuration for the P1M Tooling Plate Cylinder. Alternate porting options are available at an additional cost. 2 4 ROD END #1 ROD END #2 2 4 4 2 4 2 2 4 ROD END #1 2 4 ROD END #2 ROD END #1 ROD END #2 2 4 Both Ports Cap Face (Axial) Both Ports Cap (Radial) Tooling Plate Cylinder P1M Series E23 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Catalog 0900P-E Ordering Information P1M How to Order P1M Series Tooling Plate Cylinders 1 Porting options K, P, and T are not available with rear mountings. 2 When selecting the mount, stroke lengths below 10mm will not receive a head foot bracket. 3 Special Tooling Pate configuration. 4 When ordering double rod style cylinders, please be clear as to which end of the cylinder the tooling plate is to be incorporated as related to porting. The standard rod end configuration for Rod End # 2 (Non Tooling Plate end) is a designator # 6, metric female. Alternate rod ends are available and please consult Section A, P1M Cylinders for how to order. 5 Bumpers for this option are polyurethane. Piston, rod, and body end seals are fluorocarbon. Please review the following specification page for additional information. 6 For information regarding sensors, please refer to Electronic Sensors section. 7 Not available for 12-25mm bores. Minimum / Maximum Stroke Lengths (mm) Bore Size Minimum Stroke Maximum Stroke Single Rod Double Rod Single or Double Rod 12 5 5 60 16 5 5 70 20 5 8 85 25 5 8 85 32 5 9 100 40 5 12 100 50 5 20 100 C F D M A 6 N Cylinder Style C Basic, no mountings H Rear Flange 1 F Foot Mount 2 Cylinder Option F Guided Tool Plate G Special MTO Tooling Plate 3 B Blank Tooling Plate Function D Double Acting K Double Acting, Double Rod 4 Stroke in mm Port Type & Location BSPP G Head & Cap Radial H Both in Head J Both in Cap Radial K Both in Cap Axial NPTF 7 N Head & Cap Radial M Both in Head L Both in Cap Radial P Both in Cap Axial BSPT 7 Q Head & Cap Radial R Both in Head S Both in Cap Radial T Both in Cap Axial Rod Threads 6 Metric Female 3 Special 4 Piston Rod & Bearings A Long Bearing Stainless Steel Rod (standard for 12-25mm bores) C Long Bearing Chrome Plated Rod (N/A for 12-25mm bores) Bumpers, Magnets, Seals B Std. Seals, Bumpers, No Magnet F Fluorocarbon Seals, Bumpers 5, No Magnet M Std. Seals, Bumpers, Magnetic Piston 6 Bore Size 012 12mm 016 16mm 020 20mm 025 25mm 032 32mm 040 40mm 050 50mm 032 020 Tooling Plate Cylinder P1M Series E24 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Specifications Cylinder Specifications • Bore Sizes: 12, 16, 20, 25, 32, 40 and 50mm • Maximum Operating Pressure: 10 Bar or 145 PSI • Standard Operating Temperature: -20°C to +80°C, -4°F to +176°F • Optional (limited exposure) High Temperature: -10°C to +121°C, +14°F to +250°F Material Specifications • Piston Rod and Guide Rods: Hard Chrome Plated Steel, 100,000 PSI Yield (303 Stainless Steel standard on 12-25mm bores) • Piston Rod Seal: Polyurethane • Piston Rod Bearing: Multilayer PTFE with Steel Backing • Tooling Plate Guide Rod Bearing: Multilayer PTFE with Steel Backing • End Covers: Black Anodized Aluminum • Assembly and Tooling Plate Fasteners: Stainless Steel / Zinc Plated Steel • O-Rings: Nitrile Rubber, NBR • Cylinder Body: Clear Anodized Aluminum • Piston: Aluminum Alloy • Piston Seal: Nitrile Rubber, NBR • Magnet: Plastic Coated Magnetic Material • Bumpers: Polyurethane (12-25mm bores) or Hytrel® (32-50mm bores) High Temperature/Chemical Compatibility Seal Option Material* • O-Rings: Fluorocarbon, FPM • Piston Rod Seal: Fluorocarbon, FPM • Piston Seal: Fluorocarbon, FPM • Bumpers: Polyurethane (12-25mm bores) or Hytrel® (32-50mm bores) * Option intended for limited exposure to elevated temperatures over 80°C, or 176°F. Option is primarily for applications which subject the cylinder to fluids and or chemicals that have an adverse effect on external seals. If continued exposure to elevated temperatures is required, please consult the Actuator Division for alternative options. Hytrel® is a registered trademark of DuPont. Forces, Weights, Air Consumption Bore (mm) Area (cm2) Piston Rod Extend Force* (N) Retract Force* (N) Weight Air Consumption** (Liters) Dia. (mm) Area (cm2) Zero Stroke (kg) Per 10mm Stroke (kg) 12 1.1 6 0.3 68 51 0.073 0.020 0.0139 16 2.0 8 0.5 121 90 0.106 0.026 0.0246 20 3.1 10 0.8 188 141 0.184 0.040 0.0385 25 4.3 10 0.8 295 247 0.216 0.042 0.0633 32 8.0 12 1.1 483 415 0.314 0.052 0.1050 40 12.6 16 2.0 754 633 0.438 0.068 0.1620 50 19.6 20 3.1 1178 990 0.737 0.097 0.2530 *Theoretical cylinder force at 600 kPa (6 Bar). **Free air consumption per 10mm stroke length for an extend and retract stroke at 600 kPa (6 Bar). Tooling Plate Cylinder P1M Series E25 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E The following graphs represent maximum loading capacities for the standard piston option. Use of the standard piston option provides space savings by reducing the piston thickness, thus reducing overall length. Please review the following graphs to determine if the application load falls into acceptable operating ranges. In the event that the induced load falls out of the acceptable operating range, you may either increase the bore size or incorporate a magnetic piston for increased load capacity. For information regarding magnetic piston load carrying capability, please review the following page. Catalog 0900P-E Performance Data (SIDE LOAD) P1M Series Tooling Plate Performance Data – Standard Piston (MOMENT) OR Side Load Capacity (Standard Piston) 0 1 2 3 4 5 5 15 25 35 45 55 65 75 85 95 Stroke Length (mm) 12mm Bore 16mm Bore 20mm Bore 25mm Bore 32mm Bore 40mm Bore 50mm Bore Side Load (Kg-Force) Moment Load Capacity 0.00 0.20 0.40 0.60 0.80 1.00 1.20 1.40 5 15 25 35 45 55 65 75 85 95 Stroke Length (mm) 12mm Bore 16mm Bore 20mm Bore 25mm Bore 32mm Bore 40mm Bore 50mm Bore Moment (N-m) Tooling Plate Cylinder P1M Series E26 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Performance Data P1M Series Tooling Plate Performance Data – Magnetic Piston (SIDE LOAD) (MOMENT) OR Side Load Capacity (Magnetic Piston) 0 2 4 6 8 10 5 15 25 35 45 55 65 75 85 95 Stroke Length (mm) 12mm Bore 16mm Bore 20mm Bore 25mm Bore 32mm Bore 40mm Bore 50mm Bore Moment Load Capacity 0.00 0.20 0.40 0.60 0.80 1.00 1.20 1.40 5 15 25 35 45 55 65 75 85 95 Stroke Length (mm) 12mm Bore 16mm Bore 20mm Bore 25mm Bore 32mm Bore 40mm Bore 50mm Bore Moment (N-m) Tooling Plate Cylinder P1M Series E27 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E The following graph represents typical tooling plate deflection for P1M Tooling Plate Cylinders. The amount of tooling plate deflection is dependent on induced application load and the working stroke length of the cylinder. Depicted deflection is typical of a cylinder operating within the allowable side load and maximum allowable moment ranges per a given bore size and piston option. Catalog 0900P-E Performance Data P1M Series Tooling Plate Performance Data – Tooling Plate Deflection DEFLECTION 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 5 15 25 35 45 55 65 75 85 95 Stroke Length (mm) 12&16mm Bore 20mm Bore 25mm Bore 32&40mm Bore 50mm Bore Deflection (mm) Tooling Plate Deflection Tooling Plate Cylinder P1M Series E28 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E * Both Ports Head [BSPP ports (M5) for 12-25mm bores and 1/8″ NPTF ports for 32-50mm bores] is the standard porting configuration for the P1M Tooling Plate Cylinder. Alternate porting options are available at an additional cost. Catalog 0900P-E Dimensions – Both Ports Head VIEW A-A VIEW B-B A A B B ØEE EE1 (ORIFICE Ø) (2 PLACES) L° L° RT (2 PLACES) RT BG2 HL WH PM I79 (I78) + STROKE T9 (T8) + STROKE ZH9 (ZH8) + STROKE SW SF (2 PLACES) NB NB E2 E1 R SQ. E I92 S W U W SQ. Y (2 PLACES 180° APART) ØZ (2 PLACES ALL BORES 180° APART) Q SQ. ØZ (2 PLACES ONLY 32-50mm BORES 180° APART) MOUNTING HOLE CONFIGURATION (2 PLACES) Both Ports Head* Bore BG2 E E1 E2 EE EE1 HL L NB PM R RT BSPP BSPT NPTF 12 11.5 27 31 14 M5 — — 1 8 26 5.5 8.5 15.5 M4x0.7 16 12 31.5 35 16 M5 — — 1.2 8 20 7 9 20 M4x0.7 20 14.5 38.5 42.5 19.5 M5 — — 1.3 10 20 8 9 25.5 M6x1.0 25 15 41.5 45.5 21 M5 — — 1.8 10 20 8.5 9 28 M6x1.0 32 17 48 56 24 G1/8 Rc 1/8 1/8 2.7 10 25 9.5 10.5 34 M6x1.0 40 17.5 56 62.5 28 G1/8 Rc 1/8 1/8 3.4 10 20 11.5 9.5 40 M6x1.0 50 21.5 67 74.5 33.5 G1/8 Rc 1/8 1/8 4 12 20 14.5 10 50 M8x1.25 Bore I92 S SF SW U Q W WH Y Z Standard Piston Magnetic Piston I79 T9 ZH9 I78 T8 ZH8 12 3.5 6 4 5 25.4 20 14 3.5 M3x0.5 4.1 24 33.5 27.5 34.9 44.4 38.4 16 4 6 4 7 28.6 20 20 3.5 M3x0.5 4.1 26.2 35.7 29.7 37.1 46.6 40.6 20 4.5 6.9 7 9 34.9 26 27 4.5 M4x0.7 4.1 27.8 39.2 32.3 37.7 49.1 42.2 25 5 8.3 7 9 39 26 27 5 M4x0.7 4.1 28.8 42.1 33.8 38.7 52 43.7 32 4 8.3 7 10 44.5 32 30 7 M4x0.7 5.2 31.9 47.2 38.9 41 56.3 48 40 4 8.3 7 13 50.8 32 30 7 M4x0.7 5.2 32.6 47.9 39.6 42.5 57.8 49.5 50 5 12.1 9 16 63.5 38 42.8 8 M5x0.8 6.4 35.4 55.5 43.4 44.3 64.4 52.3 Tooling Plate Cylinder P1M Series E29 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Catalog 0900P-E Dimensions – Head and Cap Ported (Radial) VIEW B-B A A B B ØEE EE1 (ORIFICE Ø) (2 PLACES) L° L° RT (2 PLACES) WH PM PL I74 (I77) + STROKE ZH4 (ZH7) + STROKE T4 (T7) + STROKE BG1 HL RT SF (2 PLACES) SW NB NB E2 E1 R SQ. I91 S MOUNTING HOLE CONFIGURATION (2 PLACES) VIEW A-A E W U W SQ ØZ (2 PLACES ALL BORES 180° APART) Y (2 PLACES 180° APART) Q SQ ØZ (2 PLACES ONLY 32-50mm BORES 180° APART) Head and Cap Ported (Radial Bore BG1 E E1 E2 EE EE1 HL L NB PL PM R RT BSPP BSPT NPTF 12 16.5 27 31 14 M5 — — 1 8 26 5.5 5 8.5 15.5 M4x0.7 16 17 31.5 35 16 M5 — — 1.2 8 20 7 5 9 20 M4x0.7 20 19 38.5 42.5 19.5 M5 — — 1.3 10 20 8 5 9 25.5 M6x1.0 25 21 41.5 45.5 21 M5 — — 1.8 10 20 8.5 7 9 28 M6x1.0 32 25 48 56 24 G1/8 Rc 1/8 1/8 2.7 10 25 9.5 8 10.5 34 M6x1.0 40 25.5 56 62.5 28 G1/8 Rc 1/8 1/8 3.4 10 20 11.5 7.5 9.5 40 M6x1.0 50 27.6 67 74.5 33.5 G1/8 Rc 1/8 1/8 4 12 20 14.5 8 10 50 M8x1.25 Bore I91 S SF SW U Q W WH Y Z Standard Piston Magnetic Piston I74 T4 ZH4 I77 T7 ZH7 12 3.5 6 4 5 25.4 20 14 3.5 M3x0.5 4.1 29 38.5 32.5 39.9 49.4 43.4 16 4 6 4 7 28.6 20 20 3.5 M3x0.5 4.1 31.2 40.7 34.7 42.1 51.6 45.6 20 4.5 6.9 7 9 34.9 26 27 4.5 M4x0.7 4.1 32.3 43.7 36.8 42.2 53.6 46.7 25 5 8.3 7 9 39 26 27 5 M4x0.7 4.1 34.8 48.1 39.8 44.7 58 49.7 32 4 8.3 7 10 44.5 32 30 7 M4x0.7 5.2 39.9 55.2 46.9 49 64.3 56 40 4 8.3 7 13 50.8 32 30 7 M4x0.7 5.2 40.6 55.9 47.6 50.5 65.8 57.5 50 5 12.1 9 16 63.5 38 42.8 8 M5x0.8 6.4 41.4 61.5 49.4 50.3 70.4 58.3 Tooling Plate Cylinder P1M Series E30 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Dimensions – Both Ports Cap (Radial) VIEW B-B A A B B ØEE EE1 (ORIFICE Ø) (2 PLACES) L° L° RT (2 PLACES) BG1 RT HL WH PL I76 (I77) + STROKE ZH76 (ZH7) + STROKE T76 (T7) + STROKE SF (2 PLACES) SW NB NB E1 E2 R SQ. I91 S MOUNTING HOLE CONFIGURATION (2 PLACES) VIEW A-A E W U W SQ. Q SQ. ØZ (2 PLACES ALL BORES 180° APART) Y (2 PLACES 180° APART) ØZ (2 PLACES ONLY BORES 32-50 180° APART) Both Ports Cap (Radial) Bore BG1 E E1 E2 EE EE1 HL L NB PL R RT BSPP BSPT NPTF 12 16.5 27 31 14 M5 — — 1 8 26 5.5 5 15.5 M4x0.7 16 17 31.5 35 16 M5 — — 1.2 8 20 7 5 20 M4x0.7 20 19 38.5 42.5 19.5 M5 — — 1.3 10 20 8 5 25.5 M6x1.0 25 21 41.5 45.5 21 M5 — — 1.8 10 20 8.5 7 28 M6x1.0 32 25 48 56 24 G1/8 Rc1/8 1/8 2.7 10 25 9.5 8 34 M6x1.0 40 25.5 56 62.5 28 G1/8 Rc1/8 1/8 3.4 10 20 11.5 7.5 40 M6x1.0 50 27.6 67 74.5 33.5 G1/8 Rc1/8 1/8 4 12 20 14.5 8 50 M8x1.25 Bore I91 S SF SW U Q W WH Y Z Standard Piston Magnetic Piston I76 T76 ZH76 I77 T7 ZH7 12 3.5 6 4 5 25.4 20 14 3.5 M3x0.5 4.1 29 38.5 32.5 39.9 49.4 43.4 16 4 6 4 7 28.6 20 20 3.5 M3x0.5 4.1 31.2 40.7 34.7 42.1 51.6 45.6 20 4.5 6.9 7 9 34.9 26 27 4.5 M4x0.7 4.1 32.3 43.7 36.8 42.2 53.6 46.7 25 5 8.3 7 9 39 26 27 5 M4x0.7 4.1 34.8 48.1 39.8 44.7 58 49.7 32 4 8.3 7 10 44.5 32 30 7 M4x0.7 5.2 39.9 55.2 46.9 49 64.3 56 40 4 8.3 7 13 50.8 32 30 7 M4x0.7 5.2 40.6 55.9 47.6 50.5 65.8 57.5 50 5 12.1 9 16 63.5 38 42.8 8 M5x0.8 6.4 41.4 61.5 49.4 50.3 70.4 58.3 Tooling Plate Cylinder P1M Series E31 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Catalog 0900P-E Dimensions – Both Ports Cap Face (Axial) VIEW B-B A A B B RT (2 PLACES) ØEE EE1 (ORIFICE Ø) (2 PLACES) BG1 HL RT WH I76 (I77) +STROKE ZH76 (ZH7) + STROKE T76 (T7) + STROKE SF (2 PLACES) SW P4 P3 P2 P1 R SQ. I91 S MOUNTING HOLE CONFIGURATION (2 PLACES) VIEW A-A E E1 E2 Y (2 PLACES 180° APART) ØZ (2 PLACES ALL BORES 180° APART) W U W SQ. Q SQ. ØZ (2 PLACES ONLY BORES 32-50mm 180° APART) Both Ports Cap Face (Axial) Bore BG1 E E1 E2 EE EE1 HL P1 P2 P3 P4 R RT BSPP BSPT NPTF 12 16.5 27 31 14 M5 — — 1 8 25 9.5 13.5 13.5 15.5 M4x0.7 16 17 31.5 35 16 M5 — — 1.2 8 29.5 9.5 15.5 18 20 M4x0.7 20 19 38.5 42.5 19.5 M5 — — 1.3 10 35 13.5 24.5 21.5 25.5 M6x1.0 25 21 41.5 45.5 21 M5 — — 1.8 10 38.5 14 27.5 24.5 28 M6x1.0 32 25 48 56 24 G1/8 Rc1/8 1/8 2.7 10 45.5 16.5 31.5 28.5 34 M6x1.0 40 25.5 56 62.5 28 G1/8 Rc1/8 1/8 3.4 10 51 12 23 33 40 M6x1.0 50 27.6 67 74.5 33.5 G1/8 Rc1/8 1/8 4 12 63 54.5 25 41.5 50 M8x1.25 Bore I91 S SF SW U Q W WH Y Z Standard Piston Magnetic Piston I76 T76 ZH76 I77 T7 ZH7 12 3.5 6 4 5 25.4 20 14 3.5 M3x0.5 4.1 29 38.5 32.5 39.9 49.4 43.4 16 4 6 4 7 28.6 20 20 3.5 M3x0.5 4.1 31.2 40.7 34.7 42.1 51.6 45.6 20 4.5 6.9 7 9 34.9 26 27 4.5 M4x0.7 4.1 32.3 43.7 36.8 42.2 53.6 46.7 25 5 8.3 7 9 39 26 27 5 M4x0.7 4.1 34.8 48.1 39.8 44.7 58 49.7 32 4 8.3 7 10 44.5 32 30 7 M4x0.7 5.2 39.9 55.2 46.9 49 64.3 56 40 4 8.3 7 13 50.8 32 30 7 M4x0.7 5.2 40.6 55.9 47.6 50.5 65.8 57.5 50 5 12.1 9 16 63.5 38 42.8 8 M5x0.8 6.4 41.4 61.5 49.4 50.3 70.4 58.3 Tooling Plate Cylinder P1M Series E32 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Dimensions – Foot Mounted VIEW B-B VIEW A-A B A B A (4) – ØAB I7 E3 LY WF AU AU K1 AT TR AT R SQ. AJ S W AH U SQ. W Q SQ. SA2 (SA3) + STROKE ZA2 (ZA3) + STROKE TA2 (TA3) + STROKE Note: Stroke lengths below 10mm do not receive a head foot bracket. Corner thru holes cannot be used with Foot Mount if fasteners are inserted from Tooling Plate inside face (interference). Foot Mount Bore AB AH AJ AT AU E3 I7 K1 LY R S TR WF 12 4.5 17 19.5 2 8 44 29.5 2.8 34 15.5 6 35 13.5 16 4.5 19 19.5 2 8 48 33.5 2.8 38 20 6 39 13.5 20 6.5 24 20.5 3.2 9.2 62 42 4 47 25.5 6.9 50 14.5 25 6.5 26 22.5 3.2 10.7 66 46 4 50.5 28 8.3 52 15 32 6.5 30 25 3.2 11.2 71 54 4 62 34 8.3 60 17 40 6.5 33 25 3.2 11.2 78 61 4 67.5 40 8.3 67 17 50 9 39 29.5 3.2 14.7 95 72.5 5 80 50 12.1 82 18 Bore Both Ports Head Hand and Cap Ported (Radial) Both Ports Cap (Radial) Standard Piston Magnetic Piston Standard Piston Magnetic Piston Standard Piston Magnetic Piston SA2 TA2 ZA2 SA3 TA3 ZA3 SA2 TA2 ZA2 SA3 TA3 ZA3 SA2 TA2 ZA2 SA3 TA3 ZA3 12 12 48.3 42.3 22.9 59.2 53.2 17 53.3 47.3 27.9 64.2 58.2 17 53.3 47.3 27.9 64.2 58.2 16 14.2 50.5 44.5 25.1 61.4 55.4 19.2 55.5 49.5 30.1 66.4 60.4 19.2 55.5 49.5 30.1 66.4 60.4 20 15.8 56.4 49.5 25.7 66.3 59.4 20.3 60.9 54 30.2 70.8 63.9 20.3 60.9 54 30.2 70.8 63.9 25 13.8 59.3 51 23.7 69.2 60.9 19.8 5.3 57 29.7 75.2 66.9 19.8 65.3 57 29.7 75.2 66.9 32 15.9 64.4 56.1 25 73.5 65.2 23.9 72.4 64.1 33 81.5 73.2 23.9 72.4 64.1 33 81.5 73.2 40 16.6 65.1 56.8 26.5 75 66.7 24.6 73.1 64.8 34.5 83 74.7 24.6 73.1 64.8 34.5 83 74.7 50 12.4 73.7 61.6 21.3 82.6 70.5 18.4 79.7 67.6 27.3 88.6 76.5 18.4 79.7 67.6 27.3 88.6 76.5 Tooling Plate Cylinder P1M Series E33 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Catalog 0900P-E Dimensions – Rear Flange Mount VIEW A-A VIEW B-B B A B A (4) – ØFB ZF2 (ZF3) + STROKE MF UF TE2 (TE3) + STROKE WH E TF E R R SQ. R SQ. E UF BORES 32-50mm BORES 12-25mm VIEW B-B TF W W SQ. Q SQ. Rear Flange Mounting Kits can be ordered assembled to the cylinder or separately as needed. Please refer to the How To Order Code section to order the rear flange assembled to the cylinder. For separate mounting kits, please refer to page E36 for the proper kit per bore size. Rear Flange Mount Bore E FB MF R S TF U UF W WH 12 25 4.5 5.5 — 6 45 25.4 55 14 3.5 16 30 4.5 5.5 — 6 45 28.6 55 20 3.5 20 39 6.5 8 — 6.9 50.5 34.9 62 27 4.5 25 42 6.5 8 — 8.3 53 39 65 27 5 32 48 5.5 8 34 8.3 58 44.5 68 30 7 40 54 5.5 8 40 8.3 66 50.8 76 30 7 50 67 6.5 9 50 12.1 79 63.5 90 42.8 8 Bore Both Ports Head Hand and Cap Ported (Radial) Both Ports Cap (Radial) Standard Piston Magnetic Piston Standard Piston Magnetic Piston Standard Piston Magnetic Piston TE2 ZF2 TE3 ZF3 TE2 ZF2 TE3 ZF3 TE2 ZF2 TE3 ZF3 12 39 33 49.9 43.9 44 38 54.9 48.9 44 38 54.9 48.9 16 41.2 35.2 52.1 46.1 46.2 40.2 57.1 51.1 46.2 40.2 57.1 51.1 20 47.2 40.3 57.1 50.2 51.7 44.8 61.6 54.7 51.7 44.8 61.6 54.7 25 50.1 41.8 60 51.7 56.1 47.8 66 57.7 56.1 47.8 66 57.7 32 55.2 46.9 64.3 56 63.2 54.9 72.3 64 63.2 54.9 72.3 64 40 55.9 47.6 65.8 57.5 63.9 55.6 73.8 65.5 63.9 55.6 73.8 65.5 50 64.5 52.4 73.4 61.3 70.5 58.4 79.4 67.3 70.5 58.4 79.4 67.3 Tooling Plate Cylinder P1M Series E34 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Double Rod Bore S AF KF WF WH 12 6 6 M3x0.5 13.5 3.5 16 6 8 M4x0.7 13.5 3.5 20 6.9 7 M5x0.8 14.5 4.5 25 8.3 12 M6x1.0 15 5 32 8.3 13 M8x1.25 17 7 40 8.3 13 M8x1.25 17 7 50 12.1 15 M10x1.5 18 8 Bore Basic Mount – Style C Foot Mount – Style F Rear Flange Mount – Style J Standard Piston Magnetic Piston Standard Piston Magnetic Piston Standard Piston Magnetic Piston I52 ZH6 XH6 I53 ZH7 XH7 SA4 XH8 SA5 XH9 ZB2 XH2 ZB3 XH3 12 31.1 40.6 44.1 42 51.5 55 19.1 64.1 30 75 46.1 54.1 57 65 16 31.6 41.1 44.6 42.5 52 55.5 19.6 64.6 305 75.5 46.6 54.6 57.5 65.5 20 33.5 44.9 49.4 43.4 54.8 59.3 20.6 68.5 305 78.4 52.9 59.4 62.8 69.3 25 35.6 48.9 53.9 45.5 58.8 63.8 20.6 73.9 305 83.8 56.9 63.9 66.8 73.8 32 40.1 55.4 62.4 49.2 64.5 71.5 24.1 82.4 33.2 91.5 63.4 72.4 72.5 81.5 40 40.6 55.9 62.9 50.5 65.8 72.8 24.6 82.9 34.5 92.8 63.9 72.9 73.8 82.8 50 41.4 61.5 69.5 50.3 70.4 78.4 18.4 89.5 27.3 98.4 70.5 79.5 79.4 88.4 Catalog 0900P-E Dimensions – Double Rod Style S I52 (I53) + STROKE S S ZB2 (ZB3) + STROKE XH2 (XH3) + 2X STROKE END 1 END 2 END 1 END 2 END 1 END 2 WH WF + STROKE WF + STROKE XH8 (XH9) + 2X STROKE SA4 (SA5) + STROKE WH WF AF KF WH + STROKE ZH6 (ZH7) + STROKE ZH6 (ZH7) + 2X STROKE Basic Mount Foot Mount Rear Flange Mount The double rod dimensions differ from, or are in addition to, those for single rod cylinders depicted on previous pages. To determine dimensions for a double rod cylinder, first refer to the desired single rod porting style cylinder configuration you wish to incorporate on preceding pages of this catalog. After selecting the necessary dimensions from that drawing, return to this page and supplement the single rod dimensions with those shown on these dimensional tables. Note: Double rod end 2 will have a Short Bearing head as standard. Tooling Plate Cylinder P1M Series E35 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Rod End Dimensions Basic Mount Catalog 0900P-E Double Rod Style Rod End Dimensions SW Wrench Flats KK AM WH KF Thread x Depth AF WH For special rod ends, specify “3” in model number and give desired WH, AM or AF and KK or KF (length dimensions in millimeters). SW Wrench Flats KK AM WF SW Wrench Flats KK AM WF W KF Thread x Depth AF WF KF Thread x Depth AF WF W For special rod threads, specify “3” in model number and give desired AM or AF, WF and KK or KF (length dimensions in millimeters). Rod End Dimensions Foot Mount and Rear Flange Mount Foot Mount Rear Flange Mount (Revised 04-30-12) Tooling Plate Cylinder P1M Series E36 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Mountings and Service Kits Rear Flange Mount Kits Bore Size Kit Number 12 P1M-4DMB 16 P1M-4FMB 20 P1M-4HMB 25 P1M-4JMB 32 P1M-4KMB 40 P1M-4LMB 50 P1M-4MMB Seal Kits Bore Size Single Rod Cylinders Double Rod Cylinders Class 1 Seals Class 5 Seals Class 1 Seals Class 5 Seals 12 P1M-6DRN P1M-6DRV P1M-6DRT P1M-6DRP 16 P1M-6FRN P1M-6FRV P1M-6FRT P1M-6FRP 20 P1M-6HRN P1M-6HRV P1M-6HRT P1M-6HRP 25 P1M-6JRN P1M-6JRV P1M-6JRT P1M-6JRP 32 P1M-6KRN P1M-6KRV P1M-6KRT P1M-6KRP 40 P1M-6LRN P1M-6LRV P1M-6LRT P1M-6LRP 50 P1M-6MRN P1M-6MRV P1M-6MRT P1M-6MRP Foot Bracket Mounting Kits Bore Size Stroke Kit Number 12 <10mm L078290012 ≥10mm L078300012 16 <10mm L078290016 ≥10mm L078300016 20 <10mm L078290020 ≥10mm L078300020 25 <10mm L078290025 ≥10mm L078300025 32 <10mm L078290032 ≥10mm L078300032 40 <10mm L078290040 ≥10mm L078300040 50 <10mm L078290050 ≥10mm L078300050 Available Gripper Series and Sizes per P1M Tooling Plate Cylinder Bore Size Bore Size Gripper Series* and Sizes 12 P5G-AP3, P5G-AA3, P5G-AW3 16 P5G-AP3, P5G-AA3, P5G-AW3 20 P5G-AP4, P5G-AA4, P5G-AW4 25 P5G-AP4, P5G-AA4, P5G-AW4 32 P5G-AP5, P5G-AA5, P5G-AW5 40 P5G-AP5, P5G-AA5, P5G-AW5 50 P5G-AP6, P5G-AA6, P5G-AW6 Bore Size Cylinder Assembly Fasteners Piston Rod Fastener Guide Rod Fasteners Fastener Thread Fastener Torque Hex Key Fastener Thread Fastener Torque Hex Key Fastener Thread Fastener Torque Hex Key Size Nm in-lb Size Size Nm in-lb Size Size Nm in-lb Size 12 M4x0.7 1.4-1.8 12-16 2.5 M3x0.5 0.6-0.9 5-8 2 M3x0.5 0.6-0.9 5-8 2 16 M4x0.7 1.4-1.8 12-16 2.5 M4x0.7 1.4-1.8 12-16 2.5 M3x0.5 0.6-0.9 5-8 2 20 M5x0.8 2.5-2.9 22-26 3 M5x0.8 2.5-2.9 22-26 3 M4x0.7 1.4-1.8 12-16 2.5 25 M5x0.8 2.5-2.9 22-26 3 M6x1.0 4.1-4.5 36-40 4 M4x0.7 1.4-1.8 12-16 2.5 32 M6x1.0 4.1-4.5 36-40 4 M8x1.25 10.2-11.1 90-98 5 M4x0.7 1.4-1.8 12-16 2.5 40 M6x1.0 4.1-4.5 36-40 4 M8x1.25 10.2-11.1 90-98 5 M4x0.7 1.4-1.8 12-16 2.5 50 M8x1.25 10.2-11.1 90-98 5 M10x1.5 21.5-22.6 190-200 6 M5x0.8 2.5-2.9 22-26 3 Mounting Assembly Fastener Selection Chart Mounting Configuration Qty Fastener Thread Length “L” 12mm Bore 16mm Bore 20mm Bore 25mm Bore 32mm Bore 40mm Bore 50mm Bore Head (Front End Cover) Style F - Foot Mount* , Short — N/A N/A N/A N/A N/A N/A N/A Style F - Foot Mount*, Std. 2 23mm 23mm 28mm 28mm 30mm 30mm 32mm Cap (Rear End Cover) Non-Ported Cap (Ports H, M, R) Style F - Foot Mount 2 12mm 12mm 18mm 18mm 20mm 20mm 25mm Style H - Rear Flange Mount 2 12mm 12mm 18mm 18mm 20mm 20mm 25mm Ported Cap (Ports G, J, K, N, L, P Q, S, T) Style F - Foot Mount 2 20mm 20mm 23mm 23mm 30mm 30mm 30mm Style H - Rear Flange Mount 2 20mm 20mm 23mm 23mm 30mm 30mm 30mm *Use cylinder assembly fasteners to assemble front foot mount options. Short = Stroke lengths <10mm and without magnet. Std. = Stroke lengths longer than or equal to 10mm or with magnet option. 1. Determine the bore size, stroke, porting and mounting configuration of the cylinder. 2. Select the appropriate thread length fastener for both the head and cap (end cover) 3. Use a quantity of (2) each to assemble mounts to the respective end covers. 4. Ensure sufficient thread length engagement (1-1.5 x thread diameter) into mating thread. Example: 40mm bore, 15mm stroke, M porting, foot mount Head assembly fastener = 30mm thread length Cap assembly fastener = 20mm thread length (use quantity of 2 each) E37 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E P1M Series Swing Clamp Extra Low Profile Pneumatic Cylinders Contents Features and Benefits........................................................E38 Ordering Information..........................................................E39 Cylinder Specifications.......................................................E40 Performance Data...............................................................E41 Dimensions................................................................. E42-E48 Mechanical Accessories.....................................................E49 Service Kits........................................................................E50 Swing Clamp Cylinders P1M Series E38 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Features and Benefits P1M Series Swing Clamp Flexible Porting Options Both Ports Head* Both Ports Cap Both Ports Cap Face Head and Cap Ported 2 4 2 4 4 2 2 4 * Both Ports Head (NPT) is the standard porting configuration for the P1M Swing Clamp Cylinder. Alternate porting options are available at an additional cost. To retract cylinder, apply air to port #2. To extend cylinder, apply air to port #4. Swing Clamp Cylinders P1M Series E39 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E How to Order P1M Series Swing Clamp Cylinders 1 Cylinder with mounting fitted 2 Designator #3 should be selected for special rod ends only. When selecting this option, please provide rod style (male or female), thread pitch, thread depth, and wrench flat dimension. 3 Both Ports Head NPT is the standard porting arrangement for this cylinder. Alternate porting arrangements are available at an additional cost. 4 Bumpers for this option are polyurethane. Piston, rod and body end seals are fluorocarbon. Please review the following specification page for additional information. 5 Designator J should be selected for cylinders that require a special option not covered in catalog. 6 See specification table for stroke lengths available per a given bore size. Note: For sensor specifications and part numbers, please refer to the Electronic Sensors section. P1M 032 C H F M C 6 M 020 Cylinder Style C Basic, no mounting H Rear Flange 1 K Clamp Arm 1 L Rear Flange & Clamp Arm 1 Cylinder Option H Swing Clamp J Swing Clamp Special (MTO) 5 Function F Right Hand Rotation L Left Hand Rotation Stroke in mm 6 Port Type & Location BSPP “G” Threads G Head & Cap Radial H Both in Head J Both in Cap Radial K Both in Cap Axial NPT Threads N Head & Cap Radial M Both in Head 3 L Both in Cap Radial P Both in Cap Axial BSPT “R” Threads Q Head & Cap Radial R Both in Head S Both in Cap Radial T Both in Cap Axial Rod Threads 6 Metric Female 3 Special 2 Piston Rod & Bearings C Chrome Plated Carbon Steel Bumpers, Magnets & Seals B No Magnet, Bumpers, Standard Seals F No Magnet, Bumpers, Fluorocarbon Seals 4 M Magnetic Piston, Bumpers, Std. Seals V Magnetic Piston, Bumpers, Fluorocarbon Seals 4 Bore Size 032 32mm 040 40mm 050 50mm Catalog 0900P-E Ordering Information Service kits of expendable parts for fluid power cylinders are stocked in principal industrial locations across the U.S.A. and other countries. For prompt delivery and complete information, contact your nearest distributor. Seal Kit Part Numbers Bore Class 1 Class 5 32 L078660032 L078670032 40 L078660040 L078670040 50 L078660050 L078670050 Swing Clamp Cylinders P1M Series E40 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Cylinder Specifications Cylinder Specifications • Bore Sizes: 32, 40 and 50mm • Maximum Operating Pressure: 10 Bar or 145 PSI • Standard Operating Temperature: -20°C to +80°C or -4°F to +176°F • Optional High Temperature: -10°C to +121°C or +14°F to +250°F Material Specifications • Piston Rod: Hard Chrome Plated Steel, 100,000 PSI Yield • Piston Rod Bearing: Stress Proof Steel • Piston Rod Seal: Polyurethane • Outboard Rotating Mechanism Cover: 2011 T3 Aluminum • End Covers: Black Anodized Aluminum • End Cover Fasteners: Zinc Plated Carbon Steel • Cylinder Body: Clear Anodized Aluminum • O-Rings: Nitrile Rubber, NBR • Piston: Aluminum Alloy • Piston Seal: Nitrile Rubber, NBR • Magnet: Plastic Coated Magnetic Material • Bumpers: Polyurethane High Temperature Seal Option Material* • End Cover O-Rings: Fluorocarbon, FPM • Piston Rod Seal: Fluorocarbon, FPM • Piston Seal: Fluorocarbon, FPM * Option intended for limited exposure to temperatures over 80°C, or 176°F. Option is primarily for applications which subject the cylinder to fluids and or chemicals that have an adverse effect on external seals. If continued exposure to elevated temperatures is required, please consult the Cylinder Division for alternative options. Cylinder Weights, g (lbs) Bore (mm) Clamp Stroke (mm) Basic Mount Clamp Arm Mount Rear Flange Mount Arm & Flange Mount 32 10 600 (1.32) 691 (1.52) 664 (1.46) 755 (1.66) 20 673 (1.48) 764 (1.68) 736 (1.62) 827 (1.82) 40 10 700 (1.54) 791 (1.74) 782 (1.72) 873 (1.92) 20 800 (1.76) 891 (1.96) 882 (1.94) 973 (2.14) 50 20 1355 (2.98) 1527 (3.36) 1500 (3.30) 1673 (3.68) 50 1736 (3.82) 1909 (4.20) 1882 (4.14) 2055 (4.52) Clamp Forces, N (lbs) Bore (mm) Rod Dia. (mm) Net Area (cm2) Force, N (lb) at Various Operating Pressures, Mpa (PSI) 0.2 (29) 0.4 (58) 0.6 (87) 0.8 (116) 1.0 (145) 32 16 6.03 121 (27) 241 (54) 362 (81) 483 (108) 603 (136) 40 16 10.56 211 (47) 422 (95) 633 (142) 844 (190) 1056 (237) 50 20 16.49 330 (74) 660 (148) 990 (222) 1319 (297) 1649 (371) Specifications Bore (mm) 32 40 50 Rotary Stroke, mm 15 19 Clamp Stroke, mm 10/20 20/50 Allowable Moment, Nm (ft-lbs) 27 (20) 47 (35) 107 (79) Degree of Non-Rotation ±1.0° ±1.0° ±0.8° Right Hand (Clockwise) Clamping Rotation Left Hand (Counter-Clockwise) Clamping Rotation Swing Clamp Cylinders P1M Series E41 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Catalog 0900P-E Performance Data The following graph represents maximum clamp arm lengths per a given bore and operating pressure. Care should be taken not to exceed maximum operating limits outlined in this graph. Guidelines for Custom Clamp Arms 0 25 50 75 100 125 150 175 200 225 250 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Arm Length (mm) 32mm & 40mm Bores 50mm Bore Pressure (MPa) 0.000 0.005 0.010 0.015 0.020 0.025 0.030 20 40 60 80 100 120 140 160 180 200 32mm & 40mm Bores 50mm Bore Cylinder Speed (mm/s) Moment of Inertia (kg-m2) The following graph represents maximum operating speeds per a given inertia moment when incorporating a custom clamp arm. Exceeding the parameters outlined in the graph will lead to internal cylinder component damage. Please refer to the following page for examples and formulas when designing the clamp arm to be applied. Swing Clamp Cylinders P1M Series E42 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Dimensions – Head Ported Head Ported Dimensions Bore AF BG1 BG2 E E1 E2 EE EE1 HL I12 I91 I92 KF BSPP BSPT NPTF 32 18 46.5 17 48 56 24 G 1/8 Rc 1/8 1/8 1.1 9 5.5 13.5 4 M10x1.5 40 18 39 17.5 56 62.5 28 G 1/8 Rc 1/8 1/8 1.5 9 5.5 10 4 M10x1.5 50 25 47.5 23.5 67 74.5 33.5 G 1/8 Rc 1/8 1/8 2 12 5.5 12 5 M12x1.75 Bore L MM NB PM R R1 RT SW -0.1 -0.2 VD WH Y Non-Magnetic Magnetic I79 ZH9 I78 ZH8 32 25 16 9.5 30.5 34 10.5 M6x1 14 3 6.5 30 h9 67 92.5 76 101.5 40 20 16 11.5 22 40 10.5 M6x1 14 3 6.5 30 h9 60 92.5 70 102.5 50 20 20 14.5 28 50 13.5 M8x1.25 17 3.5 7.5 37 h9 72.5 113 81.5 122 * Both Ports Head (NPT) is the standard porting configuration for the P1M Swing Clamp Cylinder. Alternate porting options are available at an additional cost. R E2 E1 ØMM R E L° L° NB NB SW ØY I12 WH VD PM I79 (I78) + CLAMP STROKE ZH9 (ZH8) + 2X CLAMP STROKE KF AF I91 BG1 BG2 I92 RT HL ØR1 I91 MTG. HOLES @180° 2 PLACES EACH SIDE HL HL ØR1 ØR1 MOUNTING HOLE CONFIGURATION (2 PLACES) 2X ØEE PORT, ØEE1 ORIFICE Swing Clamp Cylinders P1M Series E43 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Catalog 0900P-E Dimensions – Head and Cap Ported Head and Cap Ported Dimensions Bore AF BG1 BG2 E E1 E2 EE EE1 EE2 HL I12 I91 I92 KF BSPP BSPT NPTF 32 18 46.5 25 48 56 24 G 1/8 Rc 1/8 1/8 1.1 2.7 9 5.5 13.5 11.5 M10x1.5 40 18 39 25.5 56 62.5 28 G 1/8 Rc 1/8 1/8 1.5 3.4 9 5.5 10 12 M10x1.5 50 25 47.5 29.5 67 74.5 33.5 G 1/8 Rc 1/8 1/8 2 4 12 5.5 12 11 M12x1.75 Bore L MM NB PL PM R R1 RT SW -0.1 -0.2 VD WH Y Non-Magnetic Magnetic I79 ZH9 I78 ZH8 32 25 16 9.5 8 30.5 34 10.5 M6x1 14 3 6.5 30 h9 75 100.5 84 109.5 40 20 16 11.5 7.5 22 40 10.5 M6x1 14 3 6.5 30 h9 68 100.5 78 110.5 50 20 20 14.5 8 28 50 13.5 M8x1.25 17 3.5 7.5 37 h9 78.5 119 87.5 128 E2 E1 ØMM R E R NB NB L° L° SW I12 VD I79 (I78) + CLAMP STROKE ZH9 (ZH8) + 2X CLAMP STROKE WH ØY PM PL KF AF ØEE PORT ØEE1 ORIFICE ØEE PORT ØEE2 ORIFICE I91 BG1 ØR1 I92 BG2 ØR1 HL HL MOUNTING HOLE CONFIGURATION (2 PLACES) RT HL ØR1 I91 MTG. HOLES @180° 2 PLACES EACH SIDE Swing Clamp Cylinders P1M Series E44 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Dimensions – Cap Ported Radial R ØMM R E NB NB L° L° E2 E1 SW I12 VD I79 (I78) + CLAMP STROKE ZH9 (ZH8) + 2X CLAMP STROKE KF AF WH ØY ØEE PORT PL ØEE1 ORIFICE I91 BG1 ØR1 I92 BG2 ØR1 HL HL MOUNTING HOLE CONFIGURATION (2 PLACES) RT HL ØR1 I91 MTG. HOLES @180° 2 PLACES EACH SIDE Cap Radial Ported Dimensions Bore AF BG1 BG2 E E1 E2 EE EE1 HL I12 I91 I92 KF BSPP BSPT NPTF 32 18 46.5 25 48 56 24 G 1/8 Rc 1/8 1/8 1.1 9 5.5 13.5 11.5 M10x1.5 40 18 39 25.5 56 62.5 28 G 1/8 Rc 1/8 1/8 1.5 9 5.5 10 12 M10x1.5 50 25 47.5 29.5 67 74.5 33.5 G 1/8 Rc 1/8 1/8 2 12 5.5 12 11 M12x1.75 Bore L MM NB PL R R1 RT SW -0.1 -0.2 VD WH Y Non-Magnetic Magnetic I79 ZH9 I78 ZH8 32 25 16 9.5 8 34 10.5 M6x1 14 3 6.5 30 h9 75 100.5 84 109.5 40 20 16 11.5 7.5 40 10.5 M6x1 14 3 6.5 30 h9 68 100.5 78 110.5 50 20 20 14.5 8 50 13.5 M8x1.25 17 3.5 7.5 37 h9 78.5 119 87.5 128 Swing Clamp Cylinders P1M Series E45 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Catalog 0900P-E Dimensions – Cap Rear Face Porting R E2 E1 SW P2 P3 P4 P1 ØMM R E I12 VD I79 (I78) + CLAMP STROKE ZH9 (ZH8) + 2X CLAMP STROKE WH ØY 2X ØEE PORT, ØEE1 ORIFICE I91 BG1 I92 BG2 ØR1 HL ØR1 HL MOUNTING HOLE CONFIGURATION (2 PLACES) KF AF RT HL ØR1 I91 MTG. HOLES @180° 2 PLACES EACH SIDE Cap Rear Face Ported Dimensions Bore AF BG1 BG2 E E1 E2 EE EE1 HL I12 I91 I92 KF BSPP BSPT NPTF 32 18 46.5 25 48 56 24 G 1/8 Rc 1/8 1/8 1.1 9 5.5 13.5 11.5 M10x1.5 40 18 39 25.5 56 62.5 28 G 1/8 Rc 1/8 1/8 1.5 9 5.5 10 12 M10x1.5 50 25 47.5 29.5 67 74.5 33.5 G 1/8 Rc 1/8 1/8 2 12 5.5 12 11 M12x1.75 Bore MM P1 P2 P3 P4 R R1 RT SW -0.1 -0.2 VD WH Y Non-Magnetic Magnetic I79 ZH9 I78 ZH8 32 16 45.5 16.5 32 28.5 34 10.5 M6x1 14 3 6.5 30 h9 75 100.5 84 109.5 40 16 51 12 23 33 40 10.5 M6x1 14 3 6.5 30 h9 68 100.5 78 110.5 50 20 63 54.5 25 41.5 50 13.5 M8x1.25 17 3.5 7.5 37 h9 78.5 119 87.5 128 Swing Clamp Cylinders P1M Series E46 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Dimensions – Clamp Arm Mount C D 10 B F G A H + Clamp Stroke T9 (T8) + 2X CLAMP STROKE Z9 (Z8) + 2X CLAMP STROKE Clamp Arm Mount Dimensions Bore A B C D F G H 32 18 67 20 45 25 M8x1.25 39 40 18 67 20 45 25 M8x1.25 46 50 22 88 22 63 40 M10x1.5 58 Bore Head Ported Only Head and Cap Ported Cap Radial Ported Cap Rear Face Ported Non- Magnetic Magnetic Non- Magnetic Magnetic Non- Magnetic Magnetic Non- Magnetic Magnetic T9 Z9 T8 Z8 T9 Z9 T8 Z8 T9 Z9 T8 Z8 T9 Z9 T8 Z8 32 106 63 115 72 114 71 123 80 114 71 123 80 114 71 123 80 40 106 63 116 73 114 71 124 81 114 71 124 81 114 71 124 81 50 130.5 68.5 139.5 77.5 136.5 74.5 145.5 83.5 136.5 74.5 145.5 83.5 136.5 74.5 145.5 83.5 Swing Clamp Cylinders P1M Series E47 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Rear Flange Mount Dimensions Bore E FB MF R TF UF 32 48 5.5 8 34 58 68 40 54 5.5 8 40 66 76 50 67 6.6 9 50 79 90 Bore Head Ported Only Head and Cap Ported Cap Radial Ported Non-Magnetic Magnetic Non-Magnetic Magnetic Non-Magnetic Magnetic ZF2 ZF3 ZF2 ZF3 ZF2 ZF3 32 100.5 109.5 108.5 117.5 108.5 117.5 40 100.5 110.5 108.5 118.5 108.5 118.5 50 122 131 128 137 128 137 Catalog 0900P-E Dimensions – Rear Flange Mount R TF UF MF 4X ØFB ZF2 (ZF3) + 2X CLAMP STROKE E R Rear Flange Mounting Kits can be ordered assembled to the cylinder or separately as needed. Please refer to page E49 for proper rear flange mounting kits associated with a given bore size. Swing Clamp Cylinders P1M Series E48 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Dimensions – Rear Flange/Clamp Arm Mount C G 10 F Z2 (Z3) + 2X CLAMP STROKE T2 (T3) + 2X CLAMP STROKE MF 4X ØFB RR TF UF E R B D A H + CLAMP STROKE SPANNER WRENCH PART # 0116760000 GLAND WRENCH PART # 0883060000 32mm Bore Assembly To disassemble the front end cover, the rod cover must first be removed. To do this the ring nut must be unscrewed (right-hand thread) using the spanner and gland wrench shown to the left. Order each component separately. Rear Flange and Clamp Arm Mount Dimensions Bore A B C D E F G H FB MF R TF UF 32 18 67 20 45 48 25 M8x1.25 39 5.5 8 34 58 68 40 18 67 20 45 54 25 M8x1.25 46 5.5 8 40 66 76 50 22 88 22 63 67 40 M10x1.5 58 6.5 9 50 79 90 Bore Head Ported Only Head and Cap Ported Cap Radial Ported Non-Magnetic Magnetic Non-Magnetic Magnetic Non-Magnetic Magnetic T2 Z2 T3 Z3 T2 Z2 T3 Z3 T2 Z2 T3 Z3 8932 114 71 123 80 122 79 131 88 122 79 131 88 40 114 71 124 81 122 79 132 89 122 79 132 89 50 139.5 77.5 148.5 86.5 145.5 83.5 154.5 92.5 145.5 83.5 154.5 92.5 Swing Clamp Cylinders P1M Series E49 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Catalog 0900P-E Mechanical Accessories Clamp Arm Mounting Kit 32, 40, and 50mm Bore Clamp Arm Mounting Kit Bore Part Number Fastener Torque Nm In-lbs 32 L078550000 8 - 10 70 - 88 40 L078550000 8 - 10 70 - 88 50 L078560000 14 - 16 124 - 142 Component Identification Item Number Part Description Material 1 Clamp Arm Aluminum 2 Clamp Bolt Steel 3 Hex Jam Nut Steel 4 Socket Head Cap Screw Steel 5 Lock Washer Steel Rear Flange Mount Kit 32, 40, and 50mm Bore 1 5 4 2 3 Note: To remove or install the arm on the piston rod, use a wrench to secure the arm while loosening or tightening the socket head cap screw. Do not secure any other part of the cylinder. 1 2 2 Rear Flange Mounting Kit Bore Part Number Fastener Torque Nm In-lbs 32 P1M-4KMB 3.6 - 4.0 32 - 36 40 P1M-4LMB 3.6 - 4.0 32 - 36 50 P1M-4MMB 8.0 - 9.0 72 - 80 Component Identification Item Number Part Description Material 1 Flange Aluminum 2 Socket Head Cap Screw Steel E50 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics Swing Clamp Cylinders P1M Series E Catalog 0900P-E Service Kits Seal Kits Bore Class 1 Class 5 32 L078660032 L078670032 40 L078660040 L078670040 50 L078660050 L078670050 E51 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E LP/LPM Series Non-Lube Air Cylinder Contents Features.............................................................................E52 Ordering Information..........................................................E53 Specifications.....................................................................E54 Basic Dimensions...............................................................E55 Mounting Options...............................................................E56 Spring Data........................................................................E57 Rod Options........................................................................E58 Accessories........................................................................E59 Bumpers / Sensors.............................................................E60 Service Kits........................................................................E61 Air Cylinders LP/LPM Series E52 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Piston Rod Seal Buna-N quad seal provides positive sealing to keep pressure in and dirt out for less maintenance and trouble free performance. Piston Rod High strength steel, hard chrome plated for reliable smooth performance, long life, and extended seal life. Cylinder Body Hard coated heavy wall aluminum alloy. The tube I.D. coating has extreme hardness, excellent wear and seizure resistance, low coefficient of friction, and high corrosion resistance. This provides excellent wear qualities and quick break-a-ways. Piston Attached securely to the rod to provide maximum strength and durability. Rod Bearing High density iron provides maximum support for longer life. Heads and Caps Anodized aluminum alloy for solid, lightweight, high strength performance. This provides excellent corrosion resistance, durability, and a long lasting quality appearance. Piston Seal Buna-N quad seal provides positive sealing with air. Catalog 0900P-E Features • Reduces Design Height • Light Weight • Reduces Cylinder Overhang • Specials Available Air Cylinders LP/LPM Series E53 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Catalog 0900P-E Ordering Information How to Order LP/LPM Series Cylinders Bore Size 0.56 9/16" 0.75 3/4" 1.12 1-1/8" 1.50 1-1/2" 2.00 2" 2.50 2-1/2" 3.00 3" 4.00 4" Double Rod Cylinder Blank Single Rod K Double Rod 1.50 K N Mounting Style N Basic (Std.) Single Rod Styles 4F Head Bolt 4R Cap Bolt 2F Head Trunnion 1 2R Cap Trunnion 1 1 Cap Pivot Eye Double Rod Styles N Basic 4R Cap Bolt 2F Head Trunnion Hollow Rod Styles 1,2,5 NH Basic 4RH Cap Bolt 2FH Head Trunnion Series LP Standard LPM Magnetic Piston 5 LP L Piston Seal Blank Standard Seal L Lipseal Piston Seal 3 Seals Blank Standard V Class 5 Seals V B Bumpers Blank No Bumpers B Bumpers Both Ends H Head End Only C Cap End Only 4 (See page E60 for stroke reduction.) Spring Blank None E Spring Extend R Spring Return E S Special Feature Blank No Special Feature S Special Feature Rod End Thread Style 9 Standard Female Rod End 4 Optional Male Rod End 3 Special Rod End (specify dimensions or sketch) 9 1.25" Stroke Specify in inches. 1. Not available on 9/16" bore. 2. Hollow rods are used on double rod cylinders. All hollow rod options require the double rod prefix “K”. 3. Lipseal piston is not available on LPM Series. 4. Not available on spring extend. 5 LPM Series with hollow rod option are not available on the 9/16", 3/4" and 1-1/8" bore sizes. Note: For sensor specifications and part numbers, please refer to the Electronic Sensors section. (Revised 12-03-13) Air Cylinders LP/LPM Series E54 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Specifications • Low Profile Design • 6 Mounting Styles • 8 Bore Sizes from 9/16" to 4" • Temperature Range: -10°F to 200°F (LPM Series 140°F max.) • Strokes from 1/8" to 6" • Permanent Lubrication • Maximum Operating Pressure: 200 PSI Air Catalog 0900P-E Specifications Technical Data Push/Pull Forces Bore dia. Rod area Piston area Push/Pull PSI 40 50 60 80 100 125 150 175 200 250 9/16 Push 0.248 10 12.5 15 20 25 31 37 43 50 62 0.048 Pull 0.200 8 10 12 16 20 25 30 35 40 50 3/4 Push 0.442 17.5 22 26.5 35 44 55 66 77 88 111 0.076 Pull 0.366 14.6 18 22 29 37 46 55 64 73 92 1-1/8 Push 0.994 40 50 60 80 99 124 149 174 200 249 0.196 Pull 0.798 32 40 48 64 80 100 120 140 160 200 1-1/2 Push 1.767 71 88 106 141 177 221 265 309 353 443 0.307 Pull 1.460 58 73 88 117 146 182 219 256 292 365 2 Push 3.141 126 157 188 251 314 393 471 550 628 785 0.442 Pull 2.699 108 135 162 216 270 337 405 472 540 675 2-1/2 Push 4.908 196 245 294 393 491 613 736 859 982 1227 0.442 Pull 4.466 178 223 268 357 447 558 670 781 893 1116 3 Push 7.069 283 353 424 566 707 884 1060 1237 1414 1767 .601 Pull 6.468 259 324 389 519 649 811 973 1135 1297 1622 4 Push 12.57 503 628 754 1006 1257 1571 1885 2200 2514 3142 0.781 Pull 11.79 471 589 707 942 1178 1484 1767 2062 2356 2945 Bore Dia. Basic N Mount Weight in ounces* Add per 1/8" of Stroke (ounces) 9/16 1.1 0.08 3/4 2.0 0.1 1-1/8 5.0 0.2 1-1/2 8.5 0.4 2 11.7 0.5 2-1/2 18.6 0.6 3 25.1 0.7 4 51.1 1.1 * Base weight includes 1/8 inch of stroke. Weights – Basic Cylinders Tie Rod Torque Bore Torque (inch pounds) 9/16 8 - 10 3/4 20 - 25 1-1/8 20 - 25 1-1/2 35 - 40 2 35 - 40 2-1/2 50 - 60 3 70 - 80 4 150 - 160 Air Cylinders LP/LPM Series E55 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Bore Dia. LPM Option* LP with Lipseal Piston Option P LB XD XJ ZB Stroke P LB XD XJ ZB 9/16† 15/16 1-7/32 2 – 1-11/32 1/2 5/8 29/32 1-11/16 – 1-1/32 3/4† 31/32 1-1/4 2-1/32 1-3/16 1-3/8 1/2 21/32 15/16 1-23/32 7/8 1-1/16 1-1/8† 63/64 1-31/64 2-3/8 1-23/64 1-39/64 9/16 43/64 1-11/64 2-1/16 1-3/64 1-19/64 1-1/2 1-1/8 1-5/8 2-13/16 1-1/2 1-3/4 7/16 13/16 1-5/16 2-1/2 1-3/16 1-7/16 2 1-9/32 1-25/32 3-1/32 1-21/32 1-29/32 7/16 61/64 1-29/64 2-45/64 1-21/64 1-37/64 2-1/2 1-21/64 1-61/64 3-21/64 1-3/4 2-5/64 1/2 1 1-5/8 3 1-27/64 1-3/4 3 1-27/64 2-3/64 3-53/64 1-53/64 2-11/64 1/2 1-3/32 1-23/32 3-1/2 1-1/2 1-27/32 4 1-1/2 2-23/64 4-11/64 2 2-31/64 1/2 1-11/64 2-1/32 3-27/32 1-43/64 2-5/32 Note minimum strokes for LPM option. † These bore sizes not available for the LPM option with the hollow rod option. * The LPM option is only available with the standard quad seal. AA Diameter Bolt Circle (Mounting Holes) Across Flats EE NPT(2) 1 3 4 2 DD threaded hole for mounting C Bore and drill thru for FB S.H.C.S. (basic model). (4) places equally spaced on AA dia. Bolt circle bore sizes 1-1/8" thru 4". (2) places 180 apart on AA dia. bolt circle bore sizes 9/16" and 3/4". MM Rod Diameter KK Thread A Deep Customer rod end has neck down and chamfer for ease of assembly. May be mounted from head or cap end Y G J LB* + stroke E Diameter ZB* + stroke D P* + stroke C Bore Dia. A C D E G J P* Y AA DD EE FB KK LB* MM ZB* 9/16 0.40 1/8 7/32 1-1/8 23/64 23/64 11/32 17/64 0.875 #8-32 #10-32 #4 #8-32 5/8 1/4 3/4 3/4 0.44 1/8 1/4 1-1/2 23/64 23/64 3/8 17/64 1.219 #10-32 #10-32 #6 #10-32 21/32 5/16 25/32 1-1/8 0.62 1/8 7/16 2 1/2 1/2 27/64 3/8 1.687 #10-32 1/8 #6 5/16-24 59/64 1/2 1-3/64 1-1/2 0.62 1/8 1/2 2-5/8 1/2 1/2 1/2 3/8 2.187 1/4-28 1/8 #10 3/8-24 1 5/8 1-1/8 2 0.70† 1/8 5/8 3-1/8 1/2 1/2 9/16 3/8 2.687 1/4-28 1/8 #10 1/2-20 1-1/16 3/4 1-3/16 2-1/2 0.70† 1/8 5/8 3-3/4 5/8 5/8 5/8 7/16 3.250 5/16-24 1/4 1/4 1/2-20 1-1/4 3/4 1-3/8 3 0.75† 1/8 3/4 4-1/4 43/64 43/64 21/32 7/16 3.781 5/16-24 1/4 1/4 5/8-18 1-9/32 7/8 1-13/32 4 0.75† 1/8 7/8 5-1/2 27/32 27/32 49/64 17/32 4.937 3/8-24 3/8 5/16 3/4-16 1-5/8 1 1-3/4 Mounting Style N Cylinder Dimensions Double Acting Single Rod End, Female Rod Style No. 9 Temperature: -10°F to 200°F (optional Fluorocarbon seals). All air cylinders are permanently lubricated. LPM Series maximum temperature 140°F. * These dimensions are for the LP Series with standard piston. † For strokes less than 0.25", A dimension = 0.66". Added Length Table for LPM or Lipseal Piston Options Catalog 0900P-E Basic Dimensions Air Cylinders LP/LPM Series E56 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Head Bolt Clearance Holes Mounting Style 4F Available Head End Cap Bolt Clearance Holes Mounting Style 4R Available Cap End Head Trunnion Mounting Style 2F (9/16" bore not available) Cap Trunnion Mounting Style 2R (9/16" bore not available) Cap Pivot Eye Mounting Style 1 Bore Dia. L M CB CD FL XD* XE 9/16 1/2 1/4 3/8 3/16 21/32 1-13/32 19/32 3/4 1/2 1/4 3/8 3/16 21/32 1-7/16 3/4 1-1/8 1/2 1/4 3/8 3/16 49/64 1-13/16 3/4 1-1/2 13/16 7/16 3/4 3/8 1-1/16 2-3/16 1-3/8 2 13/16 7/16 3/4 3/8 1-1/8 2-5/16 1-3/8 2-1/2 13/16 7/16 3/4 3/8 1-1/4 2-5/8 1-3/8 3 1-9/32 9/16 1 5/8 1-21/32 3-1/16 1-7/8 4 1-9/32 9/16 1 5/8 1-11/16 3-7/16 1-7/8 Order clevis pin from accessories when required. *These dimensions are for the LP Series with standard piston. See table on the previous page for dimensions for the lipseal piston or LPM options. Bore Dia. TD TL UT XG XJ* 3/4 0.125 5/16 2-1/8 5/16 19/32 1-1/8 0.250 1/2 3 3/8 51/64 1-1/2 0.250 1/2 3-5/8 3/8 7/8 2 0.250 1/2 4-1/8 3/8 15/16 2-1/2 0.312 5/8 5 29/64 1-3/64 3 0.312 5/8 5-1/2 15/32 1-1/16 4 0.375 3/4 7 35/64 1-17/64 (Bolts not included) Clearance hole for FB Diameter S.H.C.S. on AA Diameter B.C. (See view on previous page for location) (Bolts not included) Clearance hole for FB Diameter S.H.C.S. on AA Diameter B.C. (See view on previous page for location) XG TL TL TD +.001 –.000 NITRITE COATED UT XJ* + STROKE TL TL TD +.001 –.000 NITRITE COATED UT CD Dia. for clevis pin XE Dia. FL CB L XD* + STROKE M * These dimensions are for the LP Series with standard piston. Catalog 0900P-E Mounting Options Air Cylinders LP/LPM Series E57 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Bore Dia. G Spring Return/Extend – LP Spring Return/Extend – LPM ≥ 1/8", ≤ 1" <1", ≤ 2" ≥ 1/8", >1″ >1″, ≤ 2″ LD ZM Min.* Stroke LD ZM LD ZM Min.* Stroke LD ZM 9/16 23/64 1-1/8 1-3/8 5/16 1-13/16 2-1/16 1-23/32 1-27/32 3/16 2-13/32 2-17/32 3/4 23/64 1-11/64 1-27/64 1/8 1-55/64 2-7/64 1-49/64 1-57/64 3/16 2-29/64 2-37/64 1-1/8 1/2 1-1/2 1-3/4 1/8 2-1/8 2-3/8 2-1/16 2-3/16 1/8 2-11/16 2-13/16 1-1/2 1/2 1-11/16 1-15/16 1/8 2-5/16 2-9/16 2-5/16 2-7/16 1/4 2-15/16 3-1/16 2 1/2 1-31/64 1-47/64 1/8 2-7/64 2-23/64 2-13/64 2-21/64 1/4 2-53/64 2-61/64 2-1/2 5/8 1-3/4 2 1/8 2-3/8 2-5/8 2-29/64 2-37/64 3/16 3-5/64 3-13/64 3 43/64 1-29/32 2-5/32 1/8 2-17/32 2-25/32 2-43/64 2-51/64 1/8 3-19/64 3-27/64 4 27/32 2-1/4 2-1/2 1/8 2-7/8 3-1/8 2-63/64 3-7/64 1/8 3-39/64 3- 47/64 Spring Extend & Spring Return Cylinders (Available through 2″ stroke) Bore Dia. 1/8″ to 1″ Stroke Over 1″ to 2″ Stroke Add this length to XV, XW, XY, XZ XV XW XY XZ XV XW XY XZ for Lipseal Piston 9/16 1 1-1/8 57/64 1-1/64 1-11/16 1-13/16 1-37/64 1-45/64 9/32 3/4 1-1/64 1-9/64 59/64 1-3/64 1-45/64 1-53/64 1-39/64 1-47/64 9/32 1-1/8 1-23/64 1-31/64 1-9/32 1-13/32 1-63/64 2-7/64 1-29/32 2-1/32 1/4 1-1/2 1-25/64 1-33/64 1-11/32 1-15/32 2-1/64 2-9/64 1-31/32 2-3/32 5/16 2 1-11/64 1-19/64 1-13/32 1-17/32 1-51/64 1-59/64 2-1/32 2-5/32 25/64 2-1/2 1-3/8 1-1/2 1-23/32 1-27/32 2 2-1/8 2-11/32 2-15/64 3/8 3 1-1/2 1-5/8 1-55/64 1-63/64 2-1/8 2-1/4 2-31/64 2-39/64 7/16 4 1-27/32 1-31/32 2-13/64 2-21/64 2-15/32 2-19/32 2-53/64 2-61/64 13/32 * Note minimum strokes for LPM option. 1/8 + STROKE 1/8 XZ + 2 x STROKE XY + STROKE XV + STROKE XW + STROKE Spring Return Dims. Model NLPR Spring Extend Dims. Model NLPE Spring Force Data 1/8″ to 1″ Stroke Over 1″ to 2″ Stroke Bore dia. Max. Spring Force (lbs) Spring Rate (lb/in) Bore dia. Max. Spring Force (lbs) Spring Rate (lb/in) 9/16 5.7 4.25 9/16 5.7 1.75 3/4 9 6 3/4 9 2.5 1-1/8 10 6 1-1/8 10 2.5 1-1/2 13 5.5 1-1/2 12 2.25 2 13 5.5 2 12 2.25 2-1/2 17.5 6 2-1/2 16 2.5 3 & 4 24 6.5 3 & 4 23 2.75 G G 1/8 LD + STROKE ZM + 2 x STROKE Double Rod Spring Extend & Spring Return Cylinders (Available through 2″ stroke) Catalog 0900P-E Spring Data Air Cylinders LP/LPM Series E58 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E G G 1/8 B Dia. thru on Model KNH LD + STROKE ZM + 2 x STROKE Note: Cylinders with hollow rod option should not be bottomed out during stroke. LP Double or Hollow Rod Option, LPM, Lipseal Piston Bore Dia. B G Standard Double Rod End or with Hollow Rod LPM Option LP with Lipseal Piston Option LD ZM LD ZM LD ZM 9/16 * 23/64 3/4 1 1-11/32 1-15/32 1-1/32 1-9/32 3/4 9/64 23/64 13/16 1-1/16 1-13/32 1-17/32 1-3/32 1-11/32 1-1/8 7/32 1/2 1-3/16 1-7/16 1-3/4 1-7/8 1-7/16 1-11/16 1-1/2 9/32 1/2 1-19/64 1-35/64 1-59/64 2-3/64 1-39/64 1-55/64 2 3/8 1/2 1-3/8 1-5/8 2-3/32 2-7/32 1-49/64 2-1/64 2-1/2 3/8 5/8 1-5/8 1-7/8 2-21/64 2-29/64 2 2-1/4 3 7/16 43/64 1-11/16 1-15/16 2-29/64 2-37/64 2-1/8 2-3/8 4 1/2 27/32 2-1/32 2-9/32 2-49/64 2-57/64 2-7/16 2-11/16 *Hollow rod not available on 9/16″ bore. Double or Hollow Rod Cylinders Catalog 0900P-E Rod Options Optional Male Rod End Specify #4 Bore Dia. A C KK MM 9/16 0.38 1/8 #8-32 1/4 3/4 0.50 1/8 #10-32 5/16 1-1/8 0.50 1/8 5/16-24 1/2 1-1/2 0.50 1/8 3/8-24 5/8 2 0.62 1/8 1/2-20 3/4 2-1/2 0.62 1/8 1/2-20 3/4 3 0.75 1/8 5/8-18 7/8 4 0.75 1/8 3/4-16 1 MM Rod Diameter KK Thread A C Non-Standard Rods For non-standard rod ends, please specify rod thread style 3 and provide the KK, A, and C dimensions as needed. KK Thread A C Air Cylinders LP/LPM Series E59 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E CB sq. CE A KK Thread CD Dia. for clevis pin CA Bore Part # A CA CB CD CE KK 9/16 L073810008 3/8 15/32 3/8 3/16 1-3/32 #8-32 3/4 L073810010 3/8 15/32 3/8 3/16 1-3/32 #10-32 1-1/8 L073810020 9/16 15/32 3/8 3/16 1-9/32 5/16-24 1-1/2 L073810024 5/8 23/32 3/4 3/8 1-25/32 3/8-24 2-2-1/2 L073810032 21/32 23/32 3/4 3/8 1-27/32 1/2-20 3 L073810040 21/32 1 1 5/8 2-3/8 5/8-18 4 L073810048 21/32 1 1 5/8 2-3/8 3/4-16 Clevis Bracket (Supplied with Pin) Part # E L M CB CD DD FL RE L073820012 1 13/32 7/32 25/64 3/16 9/64 9/16 3/4 L073820024 1-3/4 25/32 13/32 49/64 3/8 11/64 15/16 1-3/8 L073820040 2-1/2 1 9/16 1-1/64 5/8 17/64 1-1/4 2 Use L073820012 on 9/16″, 3/4″ and 1-1/8″ bore. Use L073820024 on 1-1/2″, 2″ and 2-1/2″ bore. Use L073820040 on 3″ and 4″ bore. Note: The Clevis Bracket is an accessory for the rod eye or the cap pivot eye and cannot be mounted directly to the cylinder. Part # SB ST SU SW TD TL TS US L073840016 1/4 7/8 13/16 5/16 .252 1/2 3/8 1-1/2 L073840020 5/16 1 15/16 3/8 .314 5/8 29/64 1-5/8 L073840024 3/8 1-1/4 1- 1/16 7/16 .377 3/4 35/64 1-7/8 Use L073840016 on 1-1/8″, 1-1/2″ and 2″ bore. Use L073840020 on 2- 1/2″ and 3″ bore. Use L073840024 on 4″ bore. M RE E sq. RE DD Dia. CD Dia. (4) for clevis pin CB FL L TL TD +.001 SU –.000 dia. thru US SW ST SB bolt size TS Clevis Pin Part # CD HP LH LP L073830012 3/16 3/32 1 29/32 L073830024 3/8 5/32 1-5/8 1-15/32 L073830040 5/8 5/32 2 1-27/32 LH LP HP Diameter thru CD Diameter Rod Eye Catalog 0900P-E Cylinder Accessories Trunnion Bracket Air Cylinders LP/LPM Series E60 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E To sense piston position, mount sensor along tie rod using 2 each small set screws. Size A Piston Travel at Midstroke (in ±0.01) (Sensor On) Minimum Activation Distance from End of Stroke (in) Head Cap 9/16 0.32 0.20 0.13 0.13 3/4 0.25 0.23 0.13 0.13 1-1/8 0.20 0.32 0.13 0.13 1-1/2 0.10 0.32 0.07 0.07 2 0.10 0.35 0.06 0.06 2-1/2 0.03 0.42 0.06 0.06 3 0.03 0.47 0.12 0.12 4 0.00 0.47 0.12 0.12 Sensor Mounting Data .86 A SET SCREWS Catalog 0900P-E Bumpers / Sensor Mounting Noise Dampening Bumpers Bumpers both ends – B Bumpers rod end – R Bumper cap end – C* Bumpers are available at either or both ends of the cylinder to reduce noise for quieter operation. Bumper material is a 70 durometer nitrile. The table shows the distance the stroke is reduced when incorporating bumpers. This varies with operating pressure as indicated in the table. Example: 1.50 NL PB9 x 0.50″ stroke. Bumpers both ends cylinder will have a working stroke of 0.43″ instead of 0.50″ operating at 80 psi. For special applications call the factory. NOTES: Bumpers shorten actual strokes and are not practical on short stroke with low operating pressure. Bumpers on Cap End or Both Ends will add the “BC” length in chart to “C” dimension (rod extension). Bumpers on Double End Cylinders will add the “BR” length in chart to the “C” dimension (rod extension). * Not available on spring extend. Stroke Reduction (in.) Using Bumpers Bore Dia. Bumper Location Dim. Operating Pressure (PSI) 0 20 40 60 80 100 0.56 Cap End BC 0.03 0.02 0.02 0.01 0.01 0.01 Head End BR 0.07 0.07 0.06 0.06 0.05 0.04 Both Ends BB 0.10 0.09 0.08 0.07 0.06 0.05 0.75 Cap End BC 0.07 0.07 0.06 0.05 0.05 0.04 Head End BR 0.07 0.06 0.05 0.05 0.04 0.03 Both Ends BB 0.14 0.13 0.11 0.10 0.09 0.07 1.12 Cap End BC 0.10 0.09 0.09 0.07 0.07 0.06 Head End BR 0.10 0.09 0.08 0.07 0.07 0.06 Both Ends BB 0.20 0.18 0.17 0.14 0.14 0.12 1.50 Cap End BC 0.11 0.10 0.09 0.08 0.07 0.06 Head End BR 0.10 0.08 0.08 0.07 0.06 0.06 Both Ends BB 0.21 0.18 0.17 0.15 0.13 0.12 2.00 Cap End BC 0.11 0.09 0.08 0.07 0.06 0.05 Head End BR 0.10 0.08 0.06 0.06 0.06 0.05 Both Ends BB 0.21 0.17 0.14 0.13 0.12 0.10 2.50 Cap End BC 0.08 0.06 0.05 0.03 0.03 0.03 Head End BR 0.10 0.07 0.06 0.05 0.05 0.04 Both Ends BB 0.18 0.13 0.11 0.08 0.08 0.07 3.00 Cap End BC 0.10 0.06 0.04 0.03 0.02 0.01 Head End BR 0.14 0.09 0.08 0.08 0.07 0.07 Both Ends BB 0.24 0.15 0.12 0.11 0.09 0.08 4.00 Cap End BC 0.10 0.08 0.05 0.03 0.03 0.02 Head End BR 0.21 0.15 0.13 0.12 0.11 0.11 Both Ends BB 0.31 0.23 0.18 0.15 0.14 0.13 Air Cylinders LP/LPM Series E61 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Seal Kits (Lipseal Piston) Bore Size Rod Dia. Single Rod Cylinders Class 1 Seals Part No. Class 5 Seals Part No. 9/16 1/4″ KS05LPL251 KS05LPL255 3/4 5/16″ KS07LPL311 KS07LPL315 1-1/8 1/2″ KS12LPL501 KS12LPL505 1-1/2 5/8″ KS15LPL621 KS15LPL625 2 3/4″ KS20LPL751 KS20LPL755 2-1/2 3/4″ KS25LPL751 KS25LPL755 3 7/8″ KS30LPL871 KS30LPL875 4 1″ KS40LPL101 KS40LPL105 Seal Kits (Standard Piston) Bore Size Rod Dia. Single Rod Cylinders Class 1 Seals Part No. Class 5 Seals Part No. 9/16 1/4″ SKS05LP251 SKS05LP255 3/4 5/16″ SKS07LP311 SKS07LP315 1-1/8 1/2″ SKS12LP501 SKS12LP505 1-1/2 5/8″ SKS15LP621 SKS15LP625 2 3/4″ SKS20LP751 SKS20LP755 2-1/2 3/4″ SKS25LP751 SKS25LP755 3 7/8″ SKS30LP871 SKS30LP875 4 1″ SKS40LP101 SKS40LP105 Catalog 0900P-E Service Kits Air Cylinders LP/LPM Series E62 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Notes E63 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E C05 & C05S Series Short Stroke Pneumatic Cylinders Contents Features…………………………………………………………………..E64 Ordering Information………………………………………………….E65 Product Specifications………………………………………………..E66 Basic Cylinder Dimensions………………………………………….E67 Short Stroke Pneumatic Cylinders C05 and C05S Series E64 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Features Cylinders, type C05 and C05S Compact short stroke cylinders available in single and double acting versions. Ideally suited for clamping and locking operations, the range includes bores from 8 to 63 mm, providing thrust forces of up to 3000 N. The design has been optimized to include the following features: Installation The compact design (with mounting holes through the cylinder body) makes the unit easy to install in confined spaces. Clean design The main body is machined from one piece, thus providing an easy to clean unit. Stainless steel piston rods are standard for corrosion resistance. Maintenance free The units are pre‑lubricated for use without additional lubrication, reducing maintenance costs and providing an improved working environment. Piston rod with internal thread. Compact installation dimensions. Simple attachment with 2 or 4 through-going tapped attachment holes. Clean external design. Short Stroke Pneumatic Cylinders C05 and C05S Series E65 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E C05S 10 Stroke, mm 50 Cylinder type Piston Rod, mm C05 Double acting Ø12-Ø63 C05S Single acting Model Code Cylinder Bore 8 8mm 12 12mm 20 20mm 32 32mm 50 50mm 63 63mm Catalog 0900P-E Ordering Information Cylinder Type Bore Size Piston Rod Port Size Stroke Double Acting C05 12 5/- M5 10 20 10/M5 M5 10 32 12/M6 G1/8 10 G1/8 25 50 16/M8 G1/4 25 63 16/M8 G1/4 25 Single Acting C05S 8 4/- M5 4 12 5/- M5 4 20 10/M5 G1/8 4 32 12/M6 G1/8 5 50 16/M8 G1/4 10 63 16/M8 G1/4 10 – – 16 – Short Stroke Pneumatic Cylinders C05 and C05S Series E66 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Specifications Note All technical data in this catalog is typical data only. Note Air quality is essential for maximum cylinder service life (see ISO 8573). Important Before attempting any external or internal work on the cylinder or any connected components, make sure the cylinder is vented and disconnect the air supply in order to ensure isolation of the air supply. Performance Specifications Working pressure Max 10 bar (145 PSI) Working temperature -20°C to +70°C (-4°F to +158°F) Pre-lubricated, further lubrication is not normally necessary. If additional lubrication is introduced it has to be continued. Material Specifications Cylinder housing Black anodized aluminium Front end cover Brass Front end cover, single action Ø50-63 Black anodized aluminium Piston rod bearing single action Ø50-63 Brass/PTFE/lead Piston, Ø8-32 mm Stainless steel Piston, Ø50-63 mm Aluminium Piston rod Stainless steel Seals Nitrile, NBR Circlip Steel spring Return spring Surface treated steel spring Quick Reference Cylinder Cylinder Piston Rod Theoretical Force at 6 Bar (N) Air 1) Consumption (I) Spring Force (N) Stroke (mm) Mass Weight Bore (kg) (mm) Area (cm2) Dia. (mm) Area (cm2) Extend Retract Max. Min. C05S‑8‑4‑4 8 0.5 4 0.13 28 — 0.0045 — — 4 0.016 C05S‑12‑5‑4 12 1.1 5 0.20 65 — 0.0099 — — 4 0.023 C05S‑20‑10‑4 20 3.1 10 0.79 184 — 0.0151 — — 4 0.067 C05S‑32‑12‑5 32 8.0 12 1.13 463 — 0.0653 — — 5 0.192 C05S‑50‑16‑10 50 19.6 16 2.01 1145 — 0.1695 — — 10 0.416 C05S‑63‑16‑10 63 31.1 16 2.01 1825 — 0.2602 — — 10 0.663 C05‑12‑5‑10 12 1.1 5 0.20 68 56 0.0186 3 2 10 0.045 C05‑20‑1 0‑10 20 3.1 10 0.79 190 143 0.0505 7 3 10 0.125 C05‑32‑12‑10 32 8.0 12 1.13 480 415 0.1236 10 6 10 0.320 C05‑32‑12‑25 32 8.0 12 1.13 480 415 0.1236 25 19 25 0.400 C05‑50‑16‑25 50 19.6 16 2.01 1180 1060 0.3167 42 35 25 0.675 C05‑63‑16‑25 63 31.1 16 2.01 1870 1750 0.4982 58 45 25 0.800 1) Consumption of free air per 10 mm stroke for a double stroke at 600 kPa (6 bar). ! Short Stroke Pneumatic Cylinders C05 and C05S Series E67 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E Catalog 0900P-E Basic Cylinder Dimensions Single Acting Type A B C D E F G H I J K L M N O P R C05S-8-4-4 20 16 18 0* 11 5.5 6 3.4 3.4 M5 5.0 4 — 13.5 — 17 — C05S-12-5-4 25 16 20 0* 13 7.0 6 3.4 3.4 M5 6.0 5 — 15.0 — 17 — C05S-20-10-4 40 20 32 0* 20 9.0 10 5.0 5.5 G1/8 9.5 10 M5 24.0 8 21 — C05S-32-12-5 55 26 45 0* 32 14.0 10 5.0 5.5 G1/8 9.5 12 M6 32.0 12 27 9 C05S-50-16-10 80 30 65 50 50 22.5 11 6.5 6.5 G1/4 11.0 16 M8 47.5 12 31 14 C05S-63-16-10 90 35 80 62 62 19.0 15 9.0 9.0 G1/4 11.0 16 M8 50.0 14 36 14 Double Acting Type A B C D E F G H I J K KA KB L M N O P R C05-12-5-10 25 27 20 0* 13 7,0 6 3.4 3.4 M5 6.0 13.0 3 5 — 16.0 — 28 — C05-20-10-10 40 30 32 0* 20 9,0 10 5.0 5.5 M5 6.0 16.0 6 10 M5 24.0 8 31 — C05-32-12-10 55 36 45 0* 32 14,0 10 5.0 5.5 G1/8 9.5 16.5 14 12 M6 32.0 12 37 9 C05-32-12-25 55 51 45 0* 32 14,0 10 5.0 5.5 G1/8 9.5 31.5 0** 12 M6 32.0 12 52 9 C05-50-16-25 80 50 65 50 50 22,5 11 6.5 6.5 G1/4 11.0 28.0 0** 16 M8 47.5 12 51 14 C05-63-16-25 90 55 80 62 62 19,0 15 9.0 9.0 G1/4 11.0 33.0 0** 16 M8 50.0 14 56 14 * Only two mounting holes (F). ** Connections in-line. C N R E D F KA K J KB A M I ØL G B H O P C N6 R E D F K J A M I ØL G B H O P Short Stroke Pneumatic Cylinders C05 and C05S Series E68 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Catalog 0900P-E Notes E69 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P1G C05(S) LP(M) P1M P1M Tooling Plate P1M Swing Clamp E P1G Series Cartridge Cylinders Contents Features…………………………………………………………………..E70 Ordering Information………………………………………………….E70 Technical Information………………………………………………….E70 Dimensions……………………………………………………………….E70 Cartridge Cylinders P1G Series E70 C086 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics E Features Ordering Information Example: P1G-S006SS-10 Technical Information Temperature: -4°F to +176°F (-20°C to +80°C) Pressure: max. 102 PSI (7 bar) min. 29 PSI (2 bar) Use clean air. Avoid side loads on the piston rod. Avoid loading the piston rod during retraction. Do not operate the cylinders with excessive inertia. Caution Ø Retract Extended 6 1.5 4 10 2.5 6 16 4.5 11 Spring Forces (N) Ø Strokes 5 10 15 6 10 13 15 10 27 32 36 16 70 78 87 Weights (g) Ø A ØB C D E F G H J KV A/ F KV1 M N 5 10 15 6 M10 X 1 8.5 M5 M3 X 0.5 9 5 18.5 25.5 32.5 9.0 9 14 5.5 3 2.4 10 M15 X 1.5 13.0 M5 M4 X 0.7 14 5 20.5 27.0 34.0 11.5 11 19 7.0 4 3.2 16 M22 X 1.5 19.0 M5 M5 X 0.8 20 6 23.5 29.5 36.0 14.0 12 27 8.0 5 4.0 Dimensions Nut – Nickel Plated Steel Bushing – Nickel Plated Brass Spring – Stainless Steel Piston Rod Seal Piston Rod – Stainless Steel Non Lube Operation Nut – Nickel Plated Brass Body – Nickel Plated Brass N KV E D C ØB A KV1 J H G M F ! Catalog 0900P-E Features Dimensions (mm) Bore Size 006 6mm 010 10mm 016 16mm P1G-S 006 SS- 10 Stroke 05 5mm 10 10mm 15 15mm Pneumatic Actuator Products General Information P6 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P Before selecting or using Parker (The Company) cylinders or related accessories, it is important that you read, understand and follow the following safety information. Training is advised before selecting and using The Company’s products. 1.0 General Instructions 1.1 Scope – This safety guide provides instructions for selecting and using (including assembling, installing, and maintaining) cylinder products. This safety guide is a supplement to and is to be used with the specific Company publications for the specific cylinder products that are being considered for use. 1.2 Fail Safe – Cylinder products can and do fail without warning for many reasons. All systems and equipment should be designed in a fail-safe mode so that if the failure of a cylinder product occurs people and property won’t be endangered. 1.3 Distribution – Provide a free copy of this safety guide to each person responsible for selecting or using cylinder products. Do not select or use The Company’s cylinders without thoroughly reading and understanding this safety guide as well as the specific Company publications for the products considered or selected. 1.4 User Responsibility – Due to very wide variety of cylinder applications and cylinder operating conditions, The Company does not warrant that any particular cylinder is suitable for any specific application. This safety guide does not analyze all technical parameters that must be considered in selecting a product. The hydraulic and pneumatic cylinders outlined in this catalog are designed to The Company’s design guidelines and do not necessarily meet the design guideline of other agencies such as American Bureau of Shipping, ASME Pressure Vessel Code etc. The user, through its own analysis and testing, is solely responsible for: • Making the final selection of the cylinders and related accessories. • Determining if the cylinders are required to meet specific design requirements as required by the Agency(s) or industry standards covering the design of the user’s equipment. • Assuring that the user’s requirements are met, OSHA requirements are met, and safety guidelines from the applicable agencies such as but not limited to ANSI are followed and that the use presents no health or safety hazards. • Providing all appropriate health and safety warnings on the equipment on which the cylinders are used. 1.5 Additional Questions – Call the appropriate Company technical service department if you have any questions or require any additional information. See the Company publication for the product being considered or used, or call 1-800-CPARKER, or go to www.parker.com, for telephone numbers of the appropriate technical service department. 2.0 Cylinder and Accessories Selection 2.1 Seals – Part of the process of selecting a cylinder is the selection of seal compounds. Before making this selection, consult the “seal information page(s)” of the publication for the series of cylinders of interest. The application of cylinders may allow fluids such as cutting fluids, wash down fluids etc. to come in contact with the external area of the cylinder. These fluids may attack the piston rod wiper and or the primary seal and must be taken into account when selecting and specifying seal compounds. Dynamic seals will wear. The rate of wear will depend on many operating factors. Wear can be rapid if a cylinder is mis-aligned or if the cylinder has been improperly serviced. The user must take seal wear into consideration in the application of cylinders. 2.2 Piston Rods – Possible consequences of piston rod failure or separation of the piston rod from the piston include, but are not limited to are: • Piston rod and or attached load thrown off at high speed. • High velocity fluid discharge. • Piston rod extending when pressure is applied in the piston retract mode. Piston rods or machine members attached to the piston rod may move suddenly and without warning as a consequence of other conditions occurring to the machine such as, but not limited to: • Unexpected detachment of the machine member from the piston rod. • Failure of the pressurized fluid delivery system (hoses, fittings, valves, pumps, compressors) which maintain cylinder position. • Catastrophic cylinder seal failure leading to sudden loss of pressurized fluid. • Failure of the machine control system. Follow the recommendations of the “Piston Rod Selection Chart and Data” in the publication for the series of cylinders of interest. The suggested piston rod diameter in these charts must be followed in order to avoid piston rod buckling. Piston rods are not normally designed to absorb bending moments or loads which are perpendicular to the axis of piston rod motion. These additional loads can cause the piston rod to fail. If these types of additional loads are expected to be imposed on the piston rod, their magnitude should be made known to our engineering department. The cylinder user should always make sure that the piston rod is securely attached to the machine member. On occasion cylinders are ordered with double rods (a piston rod extended from both ends of the cylinder). In some cases a stop is threaded on to one of the piston rods and used as an external stroke adjuster. On occasions spacers are attached to the machine member connected to the piston rod and also used as a stroke adjuster. In both cases the stops will create a pinch point and the user should consider appropriate use of guards. If these external stops are not perpendicular to the mating contact surface, or if debris is trapped between the contact surfaces, a bending moment will be placed on the piston rod, which can lead to piston rod failure. An external stop will also negate the effect of cushioning and will subject the piston rod to impact loading. Those two (2) conditions can cause piston rod failure. Internal stroke adjusters are available with and without cushions. The use of external stroke adjusters should be reviewed with our engineering department. The piston rod to piston and the stud to piston rod threaded connections are secured with an anaerobic adhesive. The strength of the adhesive decreases with increasing temperature. Cylinders which can be exposed to temperatures above +250°F (+121°C) are to be ordered with a non studded piston rod and a pinned piston to rod joint. 2.3 Cushions – Cushions should be considered for cylinder applications when the piston velocity is expected to be over 4 inches/second. Cylinder cushions are normally designed to absorb the energy of a linear applied load. A rotating mass has considerably more energy than the same mass moving in a linear mode. Cushioning for a rotating mass application should be review by our engineering department. 2.4 Cylinder Mountings – Some cylinder mounting configurations may have certain limitations such as but not limited to minimum stroke for side or foot mounting cylinders or pressure de-ratings for certain mounts. Carefully review the catalog for these types of restrictions. Always mount cylinders using the largest possible high tensile alloy steel socket head cap screws that can fit in the cylinder mounting holes and torque them to the manufacturer’s recommendations for their size. 2.5 Port Fittings – Hydraulic cylinders applied with meter out or deceleration circuits are subject to intensified pressure at piston rod end. The rod end pressure is approximately equal to: operating pressure x effective cap end area effective rod end piston area Contact your connector supplier for the pressure rating of individual connectors. 3.0 Cylinder and Accessories Installation and Mounting 3.1 Installation 3.1.1 – Cleanliness is an important consideration, and cylinders are shipped with the ports plugged to protect them from contaminants entering the ports. These plugs should not be removed until the piping is to be installed. Before making the connection to the cylinder ports, piping should be thoroughly cleaned to remove all chips or burrs which might have resulted from threading or flaring operations. Safety Guide for Selecting and Using Hydraulic, Pneumatic Cylinders and Their Accessories WARNING: Failure of the cylinder, its parts , its mounting, its connections to other objects, or its controls can result in: • Unanticipated or uncontrolled movement of the cylinder or objects connected to it. • Falling of the cylinder or objects held up by it. • Fluid escaping from the cylinder, potentially at high velocity. These events could cause death or personal injury by, for example, persons falling from high locations , being crushed or struck by heavy or fast moving objects, being pushed into dangerous equipment or situations , or slipping on escaped fluid. ! Catalog 0900P-E Safety Guide Pneumatic Actuator Products General Information P7 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P 3.1.2 – Cylinders operating in an environment where air drying materials are present such as fast-drying chemicals, paint, or weld splatter, or other hazardous conditions such as excessive heat, should have shields installed to prevent damage to the piston rod and piston rod seals. 3.1.3 – Proper alignment of the cylinder piston rod and its mating component on the machine should be checked in both the extended and retracted positions. Improper alignment will result in excessive rod gland and/or cylinder bore wear. On fixed mounting cylinders attaching the piston rod while the rod is retracted will help in achieving proper alignment. 3.1.4 – Sometimes it may be necessary to rotate the piston rod in order to thread the piston rod into the machine member. This operation must always be done with zero pressure being applied to either side of the piston. Failure to follow this procedure may result in loosening the piston to rod-threaded connection. In some rare cases the turning of the piston rod may rotate a threaded piston rod gland and loosen it from the cylinder head. Confirm that this condition is not occurring. If it does, re-tighten the piston rod gland firmly against the cylinder head. For double rod cylinders it is also important that when attaching or detaching the piston rod from the machine member that the torque be applied to the piston rod end of the cylinder that is directly attaching to the machine member with the opposite end unrestrained. If the design of the machine is such that only the rod end of the cylinder opposite to where the rod attaches to the machine member can be rotated, consult the factory for further instructions. 3.2 Mounting Recommendations 3.2.1 – Always mount cylinders using the largest possible high tensile alloy steel socket head screws that can fit in the cylinder mounting holes and torque them to the manufacturer’s recommendations for their size. 3.2.2 – Side-Mounted Cylinders – In addition to the mounting bolts, cylinders of this type should be equipped with thrust keys or dowel pins located so as to resist the major load. 3.2.3 – Tie Rod Mounting – Cylinders with tie rod mountings are recommended for applications where mounting space is limited. The standard tie rod extension is shown as BB in dimension tables. Longer or shorter extensions can be supplied. Nuts used for this mounting style should be torqued to the same value as the tie rods for that bore size. 3.2.4 – Flange Mount Cylinders – The controlled diameter of the rod gland extension on head end flange mount cylinders can be used as a pilot to locate the cylinders in relation to the machine. After alignment has been obtained, the flanges may be drilled for pins or dowels to prevent shifting. 3.2.5 – Trunnion Mountings – Cylinders require lubricated bearing blocks with minimum bearing clearances. Bearing blocks should be carefully aligned and rigidly mounted so the trunnions will not be subjected to bending moments. The rod end should also be pivoted with the pivot pin in line and parallel to axis of the trunnion pins. 3.2.6 – Clevis Mountings – Cylinders should be pivoted at both ends with centerline of pins parallel to each other. After cylinder is mounted, be sure to check to assure that the cylinder is free to swing through its working arc without interference from other machine parts. 4.0 Cylinder and Accessories Maintenance, Troubleshooting and Replacement 4.1 Storage – At times cylinders are delivered before a customer is ready to install them and must be stored for a period of time. When storage is required the following procedures are recommended. 4.1.1 – Store the cylinders in an indoor area which has a dry, clean and noncorrosive atmosphere. Take care to protect the cylinder from both internal corrosion and external damage. 4.1.2 – Whenever possible cylinders should be stored in a vertical position (piston rod up). This will minimize corrosion due to possible condensation which could occur inside the cylinder. This will also minimize seal damage. 4.1.3 – Port protector plugs should be left in the cylinder until the time of installation. 4.1.4 – If a cylinder is stored full of hydraulic fluid, expansion of the fluid due to temperature changes must be considered. Installing a check valve with free flow out of the cylinder is one method. 4.1.5 – When cylinders are mounted on equipment that is stored outside for extended periods, exposed unpainted surfaces, e.g. piston rod, must be coated with a rust-inhibiting compound to prevent corrosion. 4.2 Cylinder Trouble Shooting 4.2.1 – External Leakage 4.2.1.1 – Rod seal leakage can generally be traced to worn or damaged seals. Examine the piston rod for dents, gouges or score marks, and replace piston rod if surface is rough. Rod seal leakage could also be traced to gland wear. If clearance is excessive, replace rod bushing and seal. Rod seal leakage can also be traced to seal deterioration. If seals are soft or gummy or brittle, check compatibility of seal material with lubricant used if air cylinder, or operating fluid if hydraulic cylinder. Replace with seal material, which is compatible with these fluids. If the seals are hard or have lost elasticity, it is usually due to exposure to temperatures in excess of 165°F. (+74°C). Shield the cylinder from the heat source to limit temperature to 350°F. (+177°C.) and replace with fluorocarbon seals. 4.2.1.2 – Cylinder body seal leak can generally be traced to loose tie rods. Torque the tie rods to manufacturer’s recommendation for that bore size. Excessive pressure can also result in cylinder body seal leak. Determine maximum pressure to rated limits. Replace seals and retorque tie rods as in paragraph above. Excessive pressure can also result in cylinder body seal leak. Determine if the pressure rating of the cylinder has been exceeded. If so, bring the operating pressure down to the rating of the cylinder and have the tie rods replaced. Pinched or extruded cylinder body seal will also result in a leak. Replace cylinder body seal and retorque as in paragraph above. Cylinder body seal leakage due to loss of radial squeeze which shows up in the form of flat spots or due to wear on the O.D. or I.D. – Either of these are symptoms of normal wear due to high cycle rate or length of service. Replace seals as per paragraph above. 4.2.2 – Internal Leakage 4.2.2.1 – Piston seal leak (by-pass) 1 to 3 cubic inches per minute leakage is considered normal for piston ring construction. Virtually no static leak with lipseal type seals on piston should be expected. Piston seal wear is a usual cause of piston seal leakage. Replace seals as required. 4.2.2.2 – With lipseal type piston seals excessive back pressure due to over-adjustment of speed control valves could be a direct cause of rapid seal wear. Contamination in a hydraulic system can result in a scored cylinder bore, resulting in rapid seal wear. In either case, replace piston seals as required. 4.2.2.3 – What appears to be piston seal leak, evidenced by the fact that the cylinder drifts, is not always traceable to the piston. To make sure, it is suggested that one side of the cylinder piston be pressurized and the fluid line at the opposite port be disconnected. Observe leakage. If none is evident, seek the cause of cylinder drift in other component parts in the circuit. 4.2.3 – Cylinder Fails to Move the Load 4.2.3.1 – Pneumatic or hydraulic pressure is too low. Check the pressure at the cylinder to make sure it is to circuit requirements. 4.2.3.2 – Piston Seal Leak – Operate the valve to cycle the cylinder and observe fluid flow at valve exhaust ports at end of cylinder stroke. Replace piston seals if flow is excessive. 4.2.3.3 – Cylinder is undersized for the load – Replace cylinder with one of a larger bore size. 4.3 Erratic or Chatter Operation 4.3.1 – Excessive friction at rod gland or piston bearing due to load misalignment – Correct cylinder-to-load alignment. 4.3.2 – Cylinder sized too close to load requirements – Reduce load or install larger cylinder. 4.3.3 – Erratic operation could be traced to the difference between static and kinetic friction. Install speed control valves to provide a back pressure to control the stroke. 4.4 Cylinder Modifications, Repairs, or Failed Component – Cylinders as shipped from the factory are not to be disassembled and or modified. If cylinders require modifications, these modifications must be done at company locations or by The Company’s certified facilities. The Cylinder Division Engineering Department must be notified in the event of a mechanical fracture or permanent deformation of any cylinder component (excluding seals). This includes a broken piston rod, tie rod, mounting accessory or any other cylinder component. The notification should include all operation and application details. This information will be used to provide an engineered repair that will prevent recurrence of the failure. It is allowed to disassemble cylinders for the purpose of replacing seals or seal assemblies. However, this work must be done by strictly following all the instructions provided with the seal kits. Catalog 0900P-E Safety Guide Pneumatic Actuator Products General Information P8 Parker Hannifin Corporation Pneumatic Division Wadsworth, Ohio www.parker.com/pneumatics P Catalog 0900P-E Offer of Sale 1. Terms and Conditions. Seller’s willingness to offer Products, or accept an order for Products, to or from Buyer is subject to these Terms and Conditions or any newer version of the terms and conditions found on-line at www.parker.com/saleterms/. Seller objects to any contrary or additional terms or conditions of Buyer’s order or any other document issued by Buyer. 2. Price Adjustments; Payments. Prices stated on Seller’s quote or other documentation offered by Seller are valid for 30 days, and do not include any sales, use, or other taxes unless specifically stated, Unless otherwise specified by Seller, all prices are F.C.A. Seller’s facility (INCOTERMS 2010). Payment is subject to credit approval and is due 30 days from the date of invoice or such other term as required by Seller’s Credit Department, after which Buyer shall pay interest on any unpaid invoices at the rate of 1.5% per month or the maximum allowable rate under applicable law. 3. Delivery Dates; Title and Risk; Shipment. All delivery dates are approximate and Seller shall not be responsible for any damages resulting from any delay. Regardless of the manner of shipment, title to any products and risk of loss or damage shall pass to Buyer upon placement of the products with the shipment carrier at Seller’s facility. Unless otherwise stated, Seller may exercise its judgment in choosing the carrier and means of delivery. No deferment of shipment at Buyers’ request beyond the respective dates indicated will be made except on terms that will indemnify, defend and hold Seller harmless against all loss and additional expense. Buyer shall be responsible for any additional shipping charges incurred by Seller due to Buyer’s acts or omissions. 4. Warranty. Seller warrants that the Products sold hereunder shall be free from defects in material or workmanship for a period of twelve months from the date of delivery to Buyer or 2,000 hours of normal use, whichever occurs first. The prices charged for Seller’s products are based upon the exclusive limited warranty stated above, and upon the following disclaimer: DISCLAIMER OF WARRANTY: THIS WARRANTY COMPRISES THE SOLE AND ENTIRE WARRANTY PERTAINING TO PRODUCTS PROVIDED HEREUNDER. SELLER DISCLAIMS ALL OTHER WARRANTIES, EXPRESS AND IMPLIED, INCLUDING DESIGN, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 5. Claims; Commencement of Actions. Buyer shall promptly inspect all Products upon delivery. No claims for shortages will be allowed unless reported to the Seller within 10 days of delivery. No other claims against Seller will be allowed unless asserted in writing within 30 days after delivery. Buyer shall notify Seller of any alleged breach of warranty within 30 days after the date the defect is or should have been discovered by Buyer. Any action based upon breach of this agreement or upon any other claim arising out of this sale (other than an action by Seller for an amount due on any invoice) must be commenced within 12 months from the date of the breach without regard to the date breach is discovered. 6. LIMITATION OF LIABILITY. UPON NOTIFICATION, SELLER WILL, AT ITS OPTION, REPAIR OR REPLACE A DEFECTIVE PRODUCT, OR REFUND THE PURCHASE PRICE. IN NO EVENT SHALL SELLER BE LIABLE TO BUYER FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF, OR AS THE RESULT OF, THE SALE, DELIVERY, NON-DELIVERY, SERVICING, USE OR LOSS OF USE OF THE PRODUCTS OR ANY PART THEREOF, OR FOR ANY CHARGES OR EXPENSES OF ANY NATURE INCURRED WITHOUT SELLER’S WRITTEN CONSENT, EVEN IF SELLER HAS BEEN NEGLIGENT, WHETHER IN CONTRACT, TORT OR OTHER LEGAL THEORY. IN NO EVENT SHALL SELLER’S LIABILITY UNDER ANY CLAIM MADE BY BUYER EXCEED THE PURCHASE PRICE OF THE PRODUCTS. 7. User Responsibility. The user, through its own analysis and testing, is solely responsible for making the final selection of the system and Product and assuring that all performance, endurance, maintenance, safety and warning requirements of the application are met. The user must analyze all aspects of the application and follow applicable industry standards and Product information. If Seller provides Product or system options, the user is responsible for determining that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the Products or systems. 8. Loss to Buyer’s Property. Any designs, tools, patterns, materials, drawings, confidential information or equipment furnished by Buyer or any other items which become Buyer’s property, may be considered obsolete and may be destroyed by Seller after two consecutive years have elapsed without Buyer ordering the items manufactured using such property. Seller shall not be responsible for any loss or damage to such property while it is in Seller’s possession or control. 9. Special Tooling. A tooling charge may be imposed for any special tooling, including without limitation, dies, fixtures, molds and patterns, acquired to manufacture Products. Such special tooling shall be and remain Seller’s property notwithstanding payment of any charges by Buyer. In no event will Buyer acquire any interest in apparatus belonging to Seller which is utilized in the manufacture of the Products, even if such apparatus has been specially converted or adapted for such manufacture and notwithstanding any charges paid by Buyer. Unless otherwise agreed, Seller shall have the right to alter, discard or otherwise dispose of any special tooling or other property in its sole discretion at any time. 10. Buyer’s Obligation; Rights of Seller. To secure payment of all sums due or otherwise, Seller shall retain a security interest in the goods delivered and this agreement shall be deemed a Security Agreement under the Uniform Commercial Code. Buyer authorizes Seller as its attorney to execute and file on Buyer’s behalf all documents Seller deems necessary to perfect its security interest. 11. Improper use and Indemnity. Buyer shall indemnify, defend, and hold Seller harmless from any claim, liability, damages, lawsuits, and costs (including attorney fees), whether for personal injury, property damage, patent, trademark or copyright The items described in this document and other documents and descriptions provided by Parker Hannifin Corporation, its subsidiaries and its authorized distributors (“Seller”) are hereby offered for sale at prices to be established by Seller. This offer and its acceptance by any customer (“Buyer”) shall be governed by all of the following Terms and Conditions. Buyer’s order for any item described in its document, when communicated to Seller verbally, or in writing, shall constitute acceptance of this offer. All goods or work described will be referred to as “Products”. infringement or any other claim, brought by or incurred by Buyer, Buyer’s employees, or any other person, arising out of: (a) improper selection, improper application or other misuse of Products purchased by Buyer from Seller; (b) any act or omission, negligent or otherwise, of Buyer; (c) Seller’s use of patterns, plans, drawings, or specifications furnished by Buyer to manufacture Product; or (d) Buyer’s failure to comply with these terms and conditions. Seller shall not indemnify Buyer under any circumstance except as otherwise provided. 12. Cancellations and Changes. Orders shall not be subject to cancellation or change by Buyer for any reason, except with Seller’s written consent and upon terms that will indemnify, defend and hold Seller harmless against all direct, incidental and consequential loss or damage. Seller may change product features, specifications, designs and availability with notice to Buyer. 13. Limitation on Assignment. Buyer may not assign its rights or obligations under this agreement without the prior written consent of Seller. 14. Force Majeure. Seller does not assume the risk and shall not be liable for delay or failure to perform any of Seller’s obligations by reason of circumstances beyond the reasonable control of Seller (hereinafter “Events of Force Majeure”) Events of Force Majeure shall include without limitation: accidents, strikes or labor disputes, acts of any government or government agency, acts of nature, delays or failures in delivery from carriers or suppliers, shortages of materials, or any other cause beyond Seller’s reasonable control. 15. Waiver and Severability. Failure to enforce any provision of this agreement will not waive that provision nor will any such failure prejudice Seller’s right to enforce that provision in the future. Invalidation of any provision of this agreement by legislation or other rule of law shall not invalidate any other provision herein. The remaining provisions of this agreement will remain in full force and effect. 16. Termination. Seller may terminate this agreement for any reason and at any time by giving Buyer thirty (30) days written notice of termination. Seller may immediately terminate this agreement, in writing, if Buyer: (a) commits a breach of any provision of this agreement (b) appointments a trustee, receiver or custodian for all or any part of Buyer’s property (c) files a petition for relief in bankruptcy on its own behalf, or by a third party (d) makes an assignment for the benefit of creditors, or (e) the dissolves or liquidates all or a majority of its assets. 17. Governing Law. This agreement and the sale and delivery of all Products hereunder shall be deemed to have taken place in and shall be governed and construed in accordance with the laws of the State of Ohio, as applicable to contracts executed and wholly performed therein and without regard to conflicts of laws principles. Buyer irrevocably agrees and consents to the exclusive jurisdiction and venue of the courts of Cuyahoga County, Ohio with respect to any dispute, controversy or claim arising out of or relating to this agreement. 18. Indemnity for Infringement of Intellectual Property Rights. Seller shall have no liability for infringement of any patents, trademarks, copyrights, trade dress, trade secrets or similar rights except as provided in this Section. Seller will defend and indemnify Buyer against allegations of infringement of U.S. patents, U.S. trademarks, copyrights, trade dress and trade secrets (“Intellectual Property Rights”). Seller will defend at its expense and will pay the cost of any settlement or damages awarded in an action brought against Buyer based on an allegation that a Product sold pursuant to this Agreement infringes the Intellectual Property Rights of a third party. Seller’s obligation to defend and indemnify Buyer is contingent on Buyer notifying Seller within ten (10) days after Buyer becomes aware of such allegations of infringement, and Seller having sole control over the defense of any allegations or actions including all negotiations for settlement or compromise. If a Product is subject to a claim that it infringes the Intellectual Property Rights of a third party, Seller may, at its sole expense and option, procure for Buyer the right to continue using the Product, replace or modify the Product so as to make it noninfringing, or offer to accept return of the Product and return the purchase price less a reasonable allowance for depreciation. Notwithstanding the foregoing, Seller shall have no liability for claims of infringement based on information provided by Buyer, or directed to Products delivered hereunder for which the designs are specified in whole or part by Buyer, or infringements resulting from the modification, combination or use in a system of any Product sold hereunder. The foregoing provisions of this Section shall constitute Seller’s sole and exclusive liability and Buyer’s sole and exclusive remedy for infringement of Intellectual Property Rights. 19. Entire Agreement. This agreement contains the entire agreement between the Buyer and Seller and constitutes the final, complete and exclusive expression of the terms of sale. All prior or contemporaneous written or oral agreements or negotiations with respect to the subject matter are herein merged. 20. Compliance with Law, U. K. Bribery Act and U.S. Foreign Corrupt Practices Act. Buyer agrees to comply with all applicable laws and regulations, including both those of the United Kingdom and the United States of America, and of the country or countries of the Territory in which the Buyer may operate, including without limitation the U. K. Bribery Act, the U.S. Foreign Corrupt Practices Act (“FCPA”) and the U.S. Anti-Kickback Act (the “Anti-Kickback Act”), and agrees to indemnify and hold harmless Seller from the consequences of any violation of such provisions by Buyer, its employees or agents. Buyer acknowledges that they are familiar with the provisions of the U. K. Bribery Act, the FCPA and the Anti-Kickback Act, and certifies that Buyer will adhere to the requirements thereof. In particular, Buyer represents and agrees that Buyer shall not make any payment or give anything of value, directly or indirectly to any governmental official, any foreign political party or official thereof, any candidate for foreign political office, or any commercial entity or person, for the purpose of influencing such person to purchase products or otherwise benefit the business of Seller. 02/12